41944A 4 Mercury EXHAUST PLATE


41944A 4 EXHAUST PLATE Mercury 1175626 EXHAUST
41944A 4 EXHAUST PLATE Mercury
Rating:
28

Buy EXHAUST PLATE 41944A 4 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 19
 

Compatible models:

1175626   Mercury

Mercury entire parts catalog list:

1175626 1976,1977,1978,1979,1980,1985,1986,1988

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Group 1
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Prior to removal of the flywheel, position the number one piston in the top center position (TC). The engine should be at the top center position in order to properly install the rear gear group. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston".
Illustration 1 g02087895
(X) Marker
(Y) Alignment Mark
With the number one piston in the top center position (TC), attach a Marker to the engine and place an Alignment Mark on the vibration damper.
Remove the flywheel housing.
Illustration 2 g01151801
Remove bolts (10), thrust plate (11), and gear assembly (9).
Use Tooling (A) and a suitable press to remove the bearing from gear assembly (9).
Remove bolts (8), gear assembly (6), and shaft assembly (7).
Use Tooling (A) and a suitable press to remove the bearing from gear assembly (6).
Remove bolts (2), gear assembly (1), and shaft assembly (3).
Use Tooling (A) and a suitable press to remove the bearing from gear assembly (1).
Remove gear assembly (12).
Remove bolts (5) and gear assemblies (4).
Illustration 3 g01151842
Remove bolts (16) and shaft assembly (17).
Remove bolts (13), thrust plates (14), and adapter assemblies (15).
Use bolt (13) in order to remove the sealing plates. Remove the O-ring seals. C32 Removal Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Group 1
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Prior to removal of the flywheel, position the number one piston in the top center position (TC). The engine should be at the top center position in order to properly install the rear gear group. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston".
Illustration 4 g02087895
(X) Marker
(Y) Alignment Mark
With the number one piston in the top center position (TC), attach a Marker to the engine and place an Alignment Mark on the vibration damper.
Remove the flywheel housing.
Illustration 5 g03427967
Remove bolts (10), retainer assembly (11), the O-ring seal, and gear assembly (9).
Use Tooling (A) and a suitable press to remove the bearing from gear assembly (9).
Remove bolts (8), gear assembly (6), and stub shaft assembly (7).
Use Tooling (A) and a suitable press to remove the bearing from gear assembly (6).
Remove bolts (2), gear assembly (1), and stub shaft assembly (3).
Use Tooling (A) and a suitable press to remove the bearing from gear assembly (1).
Remove gear assembly (12).
Remove bolts (5) and gear assemblies (4).
Remove gear assembly (13) and the thrust washers.


Parts exhaust Mercury:

75836A 1
67075
 
67075 EXHAUST TUBE
1150625, 1150628, 1175626
89743
 
89743 EXHAUST TUBE
1135412GD, 1135726, 1150453BD, 1150453GD, 1150453JD, 1150625, 1150628, 1175412GD, 1175626, 1200412GD, 1200413GD, 1200628, 1220727, 1225620
Back to top