14868 Mercury FITTING

Introduction
A new Brushless motored Fuel Pump Module (BFPM) has been introduced to replace the original brushed motored Electric Fuel Pump Module (EFPM) on 3054C and C7.1 (Mech) engines.Note: Changing from EFPM to BFPM requires a change to the electrical circuit.The new BFPM is an improved design and maintains current fuel delivery performance.Removal and Installation Procedure for Four Cylinder Engines
Required Parts
Table 1
Required Parts    
Part Number     Description     Qty    
446-1895     Fuel Filter Gp     1    
432-8577     Chassis Harness As     1    
3S-2093     Cable Straps     3    Removal Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Note: Put identification marks on all hoses, on all hose assemblies, on wires and on all tube assemblies for installation purposes. Plug all hose assemblies and tube assemblies. This helps to prevent fluid loss and helps to keep contaminants from entering the system.
Turn the fuel supply to the OFF position.
Turn the battery disconnect switch to the OFF position.
Illustration 1 g03860959
Typical example
Place a suitable container below fuel filter (9) in order to catch any fuel that might be spilled. Drain the fuel filter. Refer to Operation and Maintenance Manual for the correct procedure.
Make a temporary identification mark on tube assembly (7), tube assembly (10), and tube assembly (11) .
Disconnect tube assembly (7), tube assembly (10), and tube assembly (11) from fuel priming pump (6) .
Use suitable plugs to plug the connections on fuel priming pump (6) and tube assembly (7), tube assembly (10), and tube assembly (11) .
Disconnect the wiring harness (8) .
Support fuel priming pump (6). Remove nuts (5), remove bolts (1), washers (2), mounts (3) and spacers (4). Remove fuel priming pump (6). Retain nuts, bolts, washers, mounts, and spacers. Discard existing fuel priming pump.
Illustration 2 g03860965
Typical example
Cut cable straps (12) .
Remove bolt (14) and washer (15) from clip (13). Remove clip (13) from boss (16) .
Ensure that wiring harness (8) has been disconnected from the application wiring harness. Remove nuts (not shown). Remove bolts (19), washers (18). Remove resistor assembly (17). Discard resistor assembly.Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the fuel priming pump is clean and free from wear or damage.
Illustration 3 g03860988
Typical example
Illustration 4 g03860990
Typical example
Position fuel priming pump (6) onto the application. Install spacers (4), mounts (3), washers (2), and bolts (1). Install nuts (5) to bolts (1). Tighten the fasteners to a torque of 12 N m (106 lb in).
Connect harness assembly (8) to electrical connection on fuel priming pump (6). Ensure harness assembly (8) is connected to the harness assembly for the application.
Position clip (10) to the application. Install washer (12) and bolt (11) to clip (10). Tighten bolt hand tight.
Position clip (16) to the application. Install washer (17) and bolt (18) to clip (16). Install nut (15) to bolt (18). Tighten nut hand tight.
Remove the plugs. Connect tube assembly (7), tube assembly (13), and tube assembly (14) to fuel priming pump (6) .
Position harness assembly (8) to clip (10) and clip (16) .
Tighten the fasteners to a torque of 55 N m (41 lb ft). Ensure that clip (10) and clip (16) retain position.
Secure harness assembly (8) with new cable straps (9) .Note: Ensure that all cable straps meet OEM specification.
Turn the fuel supply to the ON position.
Turn the battery disconnect switch to the ON position.
Remove the air from the fuel system. Refer to Operations and Maintenance Manual, "Fuel System