883249 Mercury FITTING, STRAIGHT


883249 FITTING, STRAIGHT Mercury 1150413CD, 1150413FY, 1150413HF, 1150413HY, 1150413ZD, 1150423FG, 1150423FY, 1150423HF, 1150423HG, 1150423HY, 1150424FY, 1150424HY, 1200413FY, 1200413HY, 1200423FG, 1200423FY, 1200423HG, 1200423HY, 1200424FY, 1200424HY, 1200453CD, 1200453EY, 1200453H FITTING
883249 FITTING, STRAIGHT Mercury
Rating:
73

Buy FITTING, STRAIGHT 883249 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 3
 

Mercury entire parts catalog list:

1150413CD 2004,2005
1150413FY 2006
1150413HF 2010
1150413HY 2006
1150413ZD 2002,2003
1150423FG 2006
1150423FY 2006
1150423HF 2010
1150423HG 2006
1150423HY 2006
1150424FY 2006
1150424HY 2006
1200413FY 2006
1200413HY 2006
1200423FG 2006
1200423FY 2006
1200423HG 2006
1200423HY 2006
1200424FY 2006
1200424HY 2006
1200453CD 2004,2005,2006
1200453EY 2006
1200453HY 2006
1225413EY 2007
1225413ZD 2002,2003
1225423EY 2007
1225424EY 2007
1250413CD 2004,2005
1250424EY 2007,2009
1250433EY 2007
1250434EY 2007

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-5518 Bearing Tool 1
B 8T-5096 Dial Indicator 1
C 8T-3052 Degree Wheel 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Install the main bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil on the main bearings for final assembly.Note: Ensure that the main bearings are installed so that bearing tabs fit into the notch in the cylinder block. The upper halves of the main bearings have the oil groove and the oil hole.
Illustration 1 g06239408
Position new upper main bearing (6) on the crankshaft. Insert the end of the upper main bearing that does not have the tab into the cylinder block. Install Tooling (A) in the oil hole of the crankshaft. Carefully rotate the crankshaft to push the upper main bearing into the cylinder block.Note: Push the upper main bearing from the side of the bearing tab with Tooling (A). If the crankshaft is pushed the wrong direction, the bearing tab will be pushed between the crankshaft and the bearing area of the cylinder block. This action can result in damage to the cylinder block and/or the crankshaft.
Illustration 2 g06239416
Install the thrust plates (7) on each side of the number 4 main bearing.Note: Install the thrust plates with the words "Block Side" toward the cylinder block.
Install the lower halves of the crankshaft main bearings in the main bearing caps.Note: Ensure that the main bearings are installed so that bearing tabs fit into the notch in the main bearing caps.
Illustration 3 g06239102
Position main bearing caps (4) on the crankshaft.Note: Ensure that the numbers on the main bearing caps match the numbers on the cylinder block. Also ensure that the "FRONT" on the main bearing cap is installed toward the front of the cylinder block.
Lubricate the threads of bolts (3) and bolts (5) with clean engine oil. Install the bolts.
Tighten bolts (3) and bolts (5) for the main bearing caps, as follows:
Tighten bolt (3) on the tab end to a torque of 258 14 N m (190 10 lb ft).
Tighten Bolt (3) on the opposite end to a torque of 258 14 N m (190 10 lb ft).
Tighten Bolt (3) on the opposite end an additional 120 5 degrees.Note: If Tooling (C) is not used, place an index mark on the bolt and the main bearing cap.
Tighten Bolt (3) on the tab end an additional 120 5 degrees .Note: If Tooling (C) is not used, place an index mark on the bolt and the main bearing cap.
Tighten Bolt (5) on the opposite side to a torque of 80 10 N m (59 7 lb ft).
Tighten Bolt (5) on the tab end to a torque of 80 10 N m (59 7 lb ft).
Repeat Step 6e thru Step 6f.
Rotate the crankshaft to ensure that the crankshaft turns freely.
Use Tooling (B) to check the crankshaft end play. Ensure that Tooling (B) is against a machined surface. The end play is controlled by the thrust plates of No. 4 main bearing (center).Crankshaft end play (new thrust plates) ... 0.10 to 0.60 mm (0.004 to 0.024 inch)End By:
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".


Parts fitting Mercury:

68728
 
68728 FITTING
11354120D, 1135412GD, 1135412MD, 1135412SD, 1135412VD, 1135412WD, 1135473UD, 1135473VD, 1135726, 1150413CD, 1150413FY, 1150413HF, 1150413HY, 1150413SD, 1150413VD, 1150413WD, 1150413ZD, 1150423FG, 1150423FY, 1150423HF, 1150423HG, 1150423HY, 1150424FY,
68727 1
 
68727 1 FITTING, (90 Degree)
111047JHD, 1115473WD, 1135412VD, 1135412WD, 1135473UD, 1135473VD, 1135473YD, 1135D73CD, 1135D73FT, 1150413CD, 1150413FY, 1150413HF, 1150413HY, 1150413VD, 1150413WD, 1150413ZD, 1150423FG, 1150423FY, 1150423HF, 1150423HG, 1150423HY, 1150424FY, 1150424H
59169 2
 
59169 2 FITTING, Tee, BLEED HOSE
1006201VB, 1010207VB, 1031203UB, 1031203UD, 1031207ZF, 1040213YL, 1043203VD, 1055207DB, 1055207VB, 1075217VD, 1100412VB, 1135473YD, 1150413VD, 1150413WD, 1150413ZD, 1200628, 1256413WD
16604
 
16604 FITTING, FUEL PUMP (STRAIGHT)
111047JHD, 1115473WD, 1135473UD, 1135473VD, 1135473YD, 1135D73CD, 1135D73FT, 1175413LD, 1175P73HY, 1200413GD, 1200453CD, 1200453EY, 1200473UD, 1200473VD, 1200473WD, 1200473YD, 1200D73AD, 1200D73CD, 1200D73ET, 1200D73HT, 1200E73EY, 1200E73HY, 1220727,
89772 2
FITTING, Straight
89772 2 FITTING, Straight
1135412VD, 1135412WD, 1135473YD, 1150413CD, 1150413FY, 1150413HF, 1150413HY, 1150413WD, 1150413ZD, 1150423FG, 1150423FY, 1150423HF, 1150423HG, 1150423HY, 1150424FY, 1150424HY, 1200413FY, 1200413HY, 1200423FG, 1200423FY, 1200423HG, 1200423HY, 1200424F
855214 1
 
855214 1 FITTING
1200473VD, 1200473WD, 1200473YD, 1200D73AD, 1225413ZD
859431
 
859431 FITTING
1090D73CD, 1115473WD, 1135473YD, 1135D73CD, 1150413CD, 1150413ZD, 1200453CD, 1200473WD, 1200473YD, 1200D73AD, 1200D73CD, 1225413ZD, 1225E73AD, 1225F23AK, 1250413CD
832076 1
 
832076 1 FITTING, Check Valve
1135412WD, 1150413WD, 1200453CD, 1200453EY, 1200453HY, 1200473WD, 1200473YD, 1200D73AD, 1200D73CD, 1200D73ET, 1200D73HT, 1200E73EY, 1200E73HY, 1225413EY, 1225413ZD, 1225423EY, 1225424EY, 1225E73AD, 1225P73DD, 1225P73ED, 1225P73HD, 1225P83ED, 1226P73E
Back to top