9590 Mercury FUEL BOWL (MIDDLE/LOWER)


9590 FUEL BOWL (MIDDLE/LOWER) Mercury 1050312LD, 1070312BC, 1070717, 10754120D, 1100312BD FUEL
9590 FUEL BOWL (MIDDLE/LOWER) Mercury
Rating:
78

Buy FUEL BOWL (MIDDLE/LOWER) 9590 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 4
 

Compatible models:

Mercury entire parts catalog list:

1050312LD 1991,1992,1993,1994,1995,1996
1070312BC 1988,1989,1990
1070717 1987
10754120D 1990,1991,1992,1993
1100312BD 1988,1989,1990,1991,1992,1993

Information:

Start By:a. remove crankshaft pulley and vibration damper Any time the crankshaft seal is removed from the wear sleeve, a new sleeve and seal must be installed as a set. If the seal is put back on the sleeve, the seal will leak. 1. Remove the bolts from adapter (1), and install two 5/16" - 13 NC forcing screws in the adapter to remove it from the drive housing. 2. Remove O-ring seal (3) and crankshaft seal (2) from adapter (1).3. Install tool (B) in the adapter bore as shown. 4. Install tool (A) between tool (B) and wear sleeve (4). Turn tool (A) until the edge of the tool makes a flat place (crease) in the wear sleeve. Do this several places around the wear sleeve until the sleeve can be removed from the end of the crankshaft by hand.Install Crankshaft Front Seal And Wear Sleeve
Any time the crankshaft seal is removed from the wear sleeve, a new sleeve and seal must be installed as a unit. If the old seal is put back on the sleeve, the seal will leak. 1. Install adapter (1) on tooling (A) as shown.
If the crankshaft seal and wear sleeve come apart during installation, the seal and sleeve become scrap, and a new seal and sleeve must be used as a replacement.
The front seal and wear sleeve cannot be exchanged with the rear seal and wear sleeve. There are grooves in the sealing lip of the seals that direct the oil back into the crankcase as the crankshaft turns. An exchange of front and rear seals would pump the oil out of the crankcase.2. Put crankcase seal (2) and wear sleeve (4) as a unit in position on adapter (1). Make sure the lip of the seal is up as shown. Install the O-ring seal on adapter (1). 3. Install tool (B) over the studs of tooling (A). Install nuts (C), and tighten the nuts evenly until the seal is against the bottom of the adapter bore.4. Remove nuts (C), tool (B) and tooling (A) from the adapter. Do not put engine oil on seal during installation. Lubrication of the seal at installation can be a false indication of leakage at a later time.5. Clean the outer surface of the crankshaft with 6V1541 Quick Cure Primer. Put 9S3265 Retaining Compound on the outside diameter crankshaft and the inside diameter of the wear sleeve.6. Put clean engine oil on the adapter O-ring seal.7. Install tooling (D) on the end of the crankshaft. 8. Install guide bolts (E) in the drive housing. Put adapter (1) in position on guide bolts (E) and over tooling (D). Make sure the wear sleeve makes contact with the end of the crankshaft. 9. Install tool (B) over the small outside diameter of tool (F) until tool (B) is against the shoulder on tool (F).10. Install tooling (B) and (F) as a unit on the guide bolts and over the locator.11. Put clean Multi-Purpose grease on the face of nut (G), and install nut (G) on the locator. Tighten nut (G) until the wear sleeve and adapter are in position.12. Remove the tooling from the engine. 13. Install bolts (5) to hold adapter (1) in position.End By:a. install crankshaft pulley and vibration damper


Parts fuel Mercury:

13430 1
FUEL FILTER
13430 1 FUEL FILTER
1070717, 1075524
16494 1
FUEL FILTER
16494 1 FUEL FILTER
1045217, 1050312BC, 1070312BC, 1090524, 1115525
14820
 
14820 FUEL CONNECTOR
1045217, 1070717
15781A 1
FUEL CONNECTOR
15781A 1 FUEL CONNECTOR
1045217, 1050312BC, 1070312BC, 1135412GD, 1150453GD, 1150453JD, 1175412GD, 1200412GD, 1200413GD
9589
 
9589 FUEL BOWL (UPPER)
1070312BC, 1070717, 10754120D
99357A 4
19017A 1
 
19017A 1 FUEL LINE
1070312BC, 1075217DD, 1075217FD, 1075217PD, 1075217VD, 10752L7DF, 10752L7FF, 1075317DB, 1075317FB, 10754120D, 1075412DB, 1075412DD, 1075412DN, 1075412FB, 1075412FY, 1090412DB, 1090412DC, 1090412DD, 1090412DN, 1090412DY, 1090412FF, 1090412FY, 1090422D
19723
 
19723 FUEL LINE
1050312LD
Back to top