27936 Mercury GASKET, TRANSFER PORT COVER


27936 GASKET, TRANSFER PORT COVER Mercury 1020100, 1020202, 1020208, 1050200, 1200203, 1500100, 1500101, 1500205, 1500206 GASKET
27936 GASKET, TRANSFER PORT COVER Mercury
Rating:
83

Buy GASKET, TRANSFER PORT COVER 27936 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 31
 

Mercury entire parts catalog list:

1020100 1970
1020202 1972
1020208 1978,1979,1980
1050200 1980,1982,1983,1984,1985,1986
1200203 1973,1974,1975,1976,1977
1500100 1970
1500101 1971,1972,1973,1974
1500205 1975
1500206 1976,1977,1978,1979

Information:


At operating temperature, the engine coolant is hot and under pressure. Steam can cause personal injury. Drain the coolant only after the engine has been stopped and the fill cap is cool enough to touch with your bare hand. Remove the fill cap from the radiator slowly to relieve pressure. Cooling system conditioner contains alkali. Avoid contact with the skin and eyes to avoid personal injury.
1. Remove plug (1) and drain remaining coolant.2. Loosen clamps (2) and slide hose (3) on tube assembly.3. Identify and disconnect wires (4).4. Disconnect hoses (5) and (6).5. Remove bolts (7) and bolts (8).6. Remove water pump and gaskets.Install Water Pump
1. Position gaskets and water pump. Install bolts (7) and (8).2. Connect hoses (5) and (6).3. Connect wires (4).4. Slide hose (3) on water pump and tighten clamps (2).5. Install plug (1).6. Fill the cooling system. Refer to the "Operation & Maintenance Manual" for the proper procedure to fill the cooling system.End By:a. install hoodDisassemble Water Pump
Start By:a. remove water pump 1. Remove bolts (2), elbow (1) and gasket from water pump. 2. Remove bolts (4) and cover (3) from housing. 3. Loosen bolt (5) approximately 6.35 mm (.250 in).4. Hit the bolt with a soft hammer in order to remove impeller (6) from the shaft.5. Remove bolt (5) and impeller (6). 6. Remove spring (7) and seal assembly (8) from the shaft. 7. Turn the housing over and remove bolt (9). 8. After the removal of bolt (9) install bolt from Tooling (A) in the shaft of gear and bearing assembly (10).9. Put plate from driver group in Tooling (A) on top of bolt, and install the remainder of Tooling (A) on gear and bearing assembly (10) as shown.10. Remove gear and bearing assembly (10) with Tooling (A). Remove the gear and bearing assembly. The gear is held in place by two pins on the bottom. 11. If necessary remove bearing (11) from the gear with Tool (B) and a press. 12. Remove retaining ring (12) from the housing with Tooling (C). Remove the bearing and shaft assembly. 13. If necessary, remove bearing (13) from the shaft with Tooling (D) and a press. 14. Turn the housing over and remove the Lip-type seal with Tooling (D). Assemble Water Pump
The Lip-type seal must be installed with the lip toward the bearings. 1. Install the lip-type seal in housing with Tooling (A) to the bottom of the seal counterbore. Put a thin layer of engine oil on the lip of the seal. 2. Use a press and Tooling (A) to install bearing (13) on shaft (14).3. Install shaft (14) and bearing assembly in housing. 4. Install retaining ring (12) in housing with Tooling (B). 5. Use a press and Tooling (A) in order to install bearing (11) on the gear.
When gear is installed, make sure the pins on the gear engage the holes in the shaft.
6. Put gear and bearing assembly (10) in position on the shaft and install washer and bolt.
Clean water only is permitted for use as a lubricant for assistance at installation. Do not damage or put hands on the wear surface of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
7. Put ceramic ring (15) in position in the rubber seal. Use hand pressure and the tool (which is with the replacement ring) in order to install the ceramic ring and rubber seal. 8. Remove the spring from the seal assembly (8). Use hand pressure and the tool (which is with the replacement ring) in order to install the seal assembly. Push seal assembly on the shaft until the seal faces make light contact. 9. Install spring (7) on the seal assembly. 10. Put impeller (6) in position on the shaft. 11. Install washer and bolt (5). Tighten the bolt to a torque of 38 1 N m (28 1 lb ft).12. Install a new gasket and cover (3) on the housing. 13. Install a new gasket on elbow (1). Position elbow (1) on the housing. Install bolts (2) that hold elbow (1) to the housing.End By:a. install water pump


Parts gasket Mercury:

25849
 
25849 GASKET(SMALL)
1040100, 1115100, 1115503, 1115525, 1500205, 1650502, 1650503, 1850503
39401
 
39401 GASKET, POWERHEAD TO MOUNTING PLATE
1020100, 1020202, 1020208, 1200203
39402
 
39402 GASKET, MOUNTING PLATE TO DRIVE SHAFT HOUSING
1020100, 1020202, 1020208, 1200203
2015
 
2015 GASKET AND PACKING SET
1020100, 1020202, 1500100, 1500101, 1650100
37816
 
37816 GASKET, CYLINDER BLOCK COVER
1500100, 1500101, 1500205
25851
 
25851 GASKET, STRAINER COVER (LARGE)
1115100, 1115503, 1115525, 1500205, 1650502, 1650503, 1850503
Back to top