3523 Mercury GASKET AND PACKING SET (1 PER CARBURETOR)


3523 GASKET AND PACKING SET (1 PER CARBURETOR) Mercury 1115100, 1115503, 1115525, 1135100, 1150503, 1150625, 1400100, 1402202, 1800100, 1850503 GASKET
3523 GASKET AND PACKING SET (1 PER CARBURETOR) Mercury
Rating:
23

Buy GASKET AND PACKING SET (1 PER CARBURETOR) 3523 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: --
 

Mercury entire parts catalog list:

1115100 1970,1971,1972
1115503 1973,1974,1976,1977
1115525 1985
1135100 1970,1971
1150503 1973,1974,1975,1976,1977,1985
1150625 1985
1400100 1970,1971
1402202 1972,1973,1974
1800100 1970,1971,1972
1850503 1973,1974,1975

Information:


Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool.
Disconnect batteries before performance of any service work.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
This Special Instruction provides the information that is necessary to install the 199-3409 Solenoid Assembly to the governor assembly. 199-3409 Solenoid Assembly
Table 1
Parts that are included in 199-3409 Solenoid Assembly
Refer to Illustration 1 for the location of parts.    
Item     Description     Qty    
1     Retainer clip     1    
2     Washer for shaft     1    
3     Spacer     2    
4     Bolt for cover     3    
5     Solenoid     1    
6     Solenoid to shaft link     1    
7     Bolt for lever     1    
8     O-ring Seal     1    
9     Cover     1    
10     Stop lever     1    
11     Guide bolt     3    
12     Formed seal     1    
13     Nut for solenoid     3    
14     Silicone lube     1    
Illustration 1 g00831460
(1) Retainer clip (2) Washer for shaft (3) Spacer (4) Bolt for cover (5) Solenoid (6) Solenoid to shaft link (7) Bolt for lever (8) O-ring seal (9) Cover (10) Stop Lever (11) Guide boltProcedure to Install the 199-3409 Solenoid Assembly
Remove the following items: former solenoid, stop lever and O-ring. Clean the installation surface.
Coat O-ring seal (8) with silicone lube and install the O-ring seal in the counterbore around the shaft.
Install the stop lever (10) and bolt for lever (7). Hold the lever in the position and torque the bolt to 8 N m (70 lb in).
Install the formed rubber seal (not shown) by pressing the round form into the cast hole in the governor housing.
Install solenoid (5). Torque the nuts for guide bolt (11) to 12 N m (106 lb in).Note: The solenoid bracket must be flush with the governor.
Coat the chamfered side of the spacer (3) with lube and install the spacer on the shaft.Note: Retract the solenoid plunger in order to gain clearance.
Coat the solenoid to shaft link (6) with lube. Install the solenoid to shaft link (6) on the shaft and the solenoid.
Coat the chamfered side of spacer (3) with lube and install spacer (3) on the shaft. Add the washer for shaft (2) and retainer clip (1) .
Check solenoid operation before attaching the cover.
Coat the edges of cover (9) with silicone lube.
Install cover (9) with bolts (4) finger tight. Press the cover inward toward the solenoid. Then, tighten the bolts.


Parts gasket Mercury:

38501
 
38501 GASKET, EXHAUST PLATE TO DRIVE SHAFT HOUSING
1035204, 1040200, 1040208, 1050200, 1060504, 1070500, 1400100, 1402202, 1402205, 1500100, 1500101, 1500205, 1500206, 1650502, 1650503, 1650506, 1700507
53650
 
53650 GASKET, CRANKCASE TO CYLINDER BLOCK
1075524, 1080500, 1080508, 1800100, 1850503, 1850506
25851
 
25851 GASKET, STRAINER COVER (LARGE)
1115100, 1115503, 1115525, 1500205, 1650502, 1650503, 1850503
65788
 
65788 GASKET
1150625, 1150628, 1175626, 1200628, 1225620
99173 2
 
99173 2 GASKET
11354120D, 1135412MD, 1135412SD, 1135412VD, 1135473UD, 1135473VD, 1150413SD, 1150413VD, 1150453JD, 1150625, 1150628, 1175413LD, 1175413MD, 1175626
Back to top