39625 Mercury GASKET, WATER PUMP BASE TO FACE PLATE (LOWER)


39625 GASKET, WATER PUMP BASE TO FACE PLATE (LOWER) Mercury 1020100, 1020202, 1020208, 1200203 GASKET
39625 GASKET, WATER PUMP BASE TO FACE PLATE (LOWER) Mercury
Rating:
48

Buy GASKET, WATER PUMP BASE TO FACE PLATE (LOWER) 39625 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 33
 

Compatible models:

Mercury entire parts catalog list:

1020100 1970
1020202 1972
1020208 1978,1979,1980
1200203 1973,1974,1975,1976,1977

Information:

start by:a) remove valve covers1. Remove fuel line (2) with tool (B). Put protective caps on all fuel openings. 2. Make a separation between rocker arm (1) and the push rod with tool (A). Put identification on each valve bridge as to its location. Remove valve bridges (3). 3. Disconnect fuel lines (4) from fuel line adapters (5). Remove locks (6). Remove adapters (5).4. Remove bolts (8) that hold the rocker shaft assembly (7) to the cylinder head. Remove rocker shaft assembly (7).Install Rocker Shaft Assembly
1. Put rocker shaft assembly (2) into position on the head.2. Put clean engine oil on the threads of bolts (1) and tighten evenly to a torque of 200 20 lb.ft. (270 25 N m). Tighten the bolts again to a torque of 330 15 lb.ft. (450 20 N m). Tighten the bolts again to a torque of 330 15 lb.ft. (450 20 N m). 3. Put clean engine oil on the O-ring for adapter (5). Install adapters (5) and locks.4. Connect fuel lines (3) to adapters (5). Tighten fuel line nuts to a torque of 30 5 lb.ft. (40 7 N m) with tool (B).5. Put clean engine oil on the valve bridge dowels. Install valve bridges (7) in their correct locations on the cylinder head.6. Put clean engine oil on the valve bridges. Make a connection between the rocker arms (4) and push rods with tool (A).7. Make an adjustment of the valves to have a clearance of .015 in. (.038 mm) for intake and .030 in. (0.76 mm) for exhaust. See VALVE CLEARANCE SETTING in TESTING AND ADUSTING.8. Install the fuel lines to fuel valves (6). Tighten the fuel line nuts to a torque of 30 5 lb.ft. (40 7 N m) with tool (B).Disassemble Rocker Shaft Assembly
start by:a) remove rocker shaft assembly 1. Remove retainer (1) from the end of the shaft.2. Remove the washers and rocker arm (2). 3. Use tool (A) to remove the pin that holds bracket (3) to the rocker arm shaft.4. Remove bracket (3), rocker arm (4) and the spring.5. Remove the remainder of the rocker arms. The center brackets do not have pins.Assemble Rocker Shaft Assembly
Make sure all parts of the rocker shaft assembly are clean before assembly.1. Put clean engine oil on shaft (3).2. Install the center springs, rocker arms and bracket. 3. Install spring (1), rocker arm (4) and bracket (2).4. Put tape around the shaft on each side of bracket (2) as shown. Put the hole in bracket (2) in alignment with the hole in shaft (3). Put a mark on each piece of tape in alignment with the hole in bracket (2). 5. Install pin (5) until it is extended .34 in. (8.6 mm) above the surface of bracket (2). Make sure pin (5) is in alignment with the marks on the tape before pin is installed. Remove the tape.6. Install rocker arm (6), washers (7) and retainer (8). Install enough washers until the end play on each end of the shaft is .005 - .040 in. (0.12 - 1.01 mm).end by:a) install rocker shaft assembly


Parts gasket Mercury:

39401
 
39401 GASKET, POWERHEAD TO MOUNTING PLATE
1020100, 1020202, 1020208, 1200203
39402
 
39402 GASKET, MOUNTING PLATE TO DRIVE SHAFT HOUSING
1020100, 1020202, 1020208, 1200203
2015
 
2015 GASKET AND PACKING SET
1020100, 1020202, 1500100, 1500101, 1650100
31402
 
31402 GASKET, CARBURETOR FLANGE
1020100, 1020202, 1500100, 1500101, 1500205, 1650100
27936
 
27936 GASKET, TRANSFER PORT COVER
1020100, 1020202, 1020208, 1050200, 1200203, 1500100, 1500101, 1500205, 1500206
75791
 
75791 GASKET, CARBURETOR FLANGE
1020208, 1050200, 1500206
5207
 
5207 GASKET, STRAINER COVER
1007209, 1018200, 1020208, 1050200
Back to top