41499 5 Mercury GASKET, Exhaust Manifold Cover


41499 5 GASKET, Exhaust Manifold Cover Mercury 1016207PD, 1016207RB, 1016207SB, 10202014D, 1020201VB GASKET
41499 5 GASKET, Exhaust Manifold Cover Mercury
Rating:
23

Buy GASKET, Exhaust Manifold Cover 41499 5 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 9
 

Compatible models:

Mercury entire parts catalog list:

1016207PD 1994
1016207RB 1995
1016207SB 1996
10202014D 1994,1995,1996,1997,1998
1020201VB 1999,2000,2001,2002,2003,2004

Information:


Table 1
Diagnostic Trouble Codes
CDL Code J1939 Code Code Description Comments
E1052 (1) 3480-17 Low Aftertreatment #1 Fuel Pressure #1 - Least Severe There are Enhanced Troubleshooting Indicators for this code.
E1052 (2) 3480-18 Low Aftertreatment #1 Fuel Pressure #1 - Moderate Severity There are not Enhanced Troubleshooting Indicators for this code.
E1053 (1) 4077-17 Low Aftertreatment #1 Fuel Pressure #2 - Least Severe There are Enhanced Troubleshooting Indicators for this code.
E1053 (2) 4077-18 Low Aftertreatment #1 Fuel Pressure #2 - Moderate Severity There are not Enhanced Troubleshooting Indicators for this code.
Table 2
Required Parts for Use with a 11/16 Fitting
8T-0855 Pressure Gauge
8T-8902 Tee
228-7089 O-Ring Seal (Tee)
6V-4144 Quick Connect Coupler
6V-3965 Fitting
3J-1907 O-Ring Seal
Required Parts for Use with a 9/16 Fitting
7X-2444 Swivel Tee
214-7568 O-Ring Seal (Tee)
6V-3965 Fitting
3J-1907 O-Ring Seal
8T-0855 Pressure Gauge
6V-4144 Quick Connect Coupler
Optional Parts
177-7860 Hose As
177-7861 Hose As
177-7862 Hose As
126-6872 9/16 Tee
8C-3309 11/16 Tee
Table 3
Associated Diagnostic Trouble Codes
5580-18 or E198
3427-5 or 5423-5
3427-6 or 5423-6
Table 4
Troubleshooting Test Steps Values Results
1. Check for Associated Diagnostic Trouble Codes
A. Establish communication between Caterpillar Electronic Technician (ET) and the Electronic Control Module (ECM) . Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. Check for associated diagnostic trouble codes.
Associated Diagnostic Trouble Codes
Result: A 5580-18 or E198 code is not active. Proceed to Test Step 2.
Result: A 5580-18 or E198 code is active.
Refer to Troubleshooting, "Fuel Pressure Is Low" for the proper troubleshooting procedure. STOP.
Result: A 3427-5, 3427-6, 5423-5 or 5423-6 code is active.
Refer to Troubleshooting, "Solenoid Valve - Test" for the proper troubleshooting procedure.
2. Record the Enhanced Troubleshooting Indicator (ETI) Code
A. Establish communication between Caterpillar Electronic Technician (ET) and the Electronic Control Module (ECM) . Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. The ETI code is located in the "Status" screen under "Enhanced Troubleshooting Information (ETI) - ARD". Record the Enhanced Troubleshooting Indicator (ETI) code.
ETI codes are not available for (2) or -18 codes.
Recorded ETI code
Result: Record the ETI code if present.
Proceed to Test Step 3.
Illustration 1 g03178918
Table 5
Troubleshooting Test Steps Values Results
3. Check for External Leaks
A. Check for external leaks. Inspect the fuel lines from the pump to the fuel manifold. Check for pinched lines or leaking lines.
External leaks
Result: A leak or pinched line was not found.
Proceed to Test Step 4.
Result: A leak or pinched line was found.
Repair all damaged lines or leaking lines. Perform the "ARD Ignition Test" by using Cat ET. Refer to System Operation and Testing and Adjusting , "ARD Fuel System - Test". If the "ARD Ignition Test" was successful, return the unit to service.
If the ARD ignition test was not successful, Proceed to Test Step 4.
Illustration 2 g03507107
Table 6
4. Check for Electrical Power at the ARD Fuel Pump
A. Turn the keyswitch to the ON position. Do not start the engine.
B. Establish communication between Cat ET and the ECM. Select "Fuel Priming Command Override" or use the manual priming switch (if equipped) in order to activate the ARD fuel pump. Refer to Troubleshooting, "Cat ET Service Features" for information about service features.
C. Check for voltage between pin 1 and pin 2 on the connector to the fuel priming pump. Check the voltage while the pump is in override. Voltage is not present unless the pump is priming.
D. Deactivate the override.
E. Turn the keyswitch to the OFF position.
F. Check the voltage at the battery.
Voltage within 3 VDC of the battery voltage
Result: The voltage at the ARD fuel pump is within 3 VDC of the battery voltage.
Proceed to Test Step 5.
Result: The voltage at the ARD fuel pump is not within 3 VDC of the battery voltage.
Refer to the machine troubleshooting schematic in order to troubleshoot the circuit for the priming pump. STOP.


Parts gasket Mercury:

62386
 
62386 GASKET, THERMOSTAT
1006201PD, 1006201RB, 1006201VB, 1006206, 1006211RD, 1007209, 1008211RD, 1010207VB, 1016207PD, 1016207RB, 1016207SB, 1018204, 10202014D, 1020201BC, 1020201VB, 1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1040200, 1040208, 1040213YL, 1041312UB, 1050302
88004
 
88004 GASKET, CARBURETOR
1018200, 1020201DB, 1020201VB
86389
 
86389 GASKET, CYLINDER BLOCK COVER
1018200, 1018204, 1020201DB, 1020201VB, 1025200
19206 1
 
19206 1 GASKET, CARBURETOR
1006201DB, 1006201PD, 1006201RB, 1006201VB, 1006206, 1006211RD, 1008211RD, 1010207VB, 1011201DB, 1016207PD, 1016207RB, 1016207SB, 10202014D, 1020201DB, 1020201VB
44426
 
44426 GASKET, ELECTRIC CHOKE
1006201DB, 1006201PD, 1006201VB, 1006206, 1006211RD, 1008211RD, 1010207VB, 1011201DB, 1016207PD, 1020201DB, 1020201VB
19207 1
GASKET
19207 1 GASKET
1006201PD, 1006201RB, 1006201VB, 1006206, 1006211RD, 1008211RD, 1010207VB, 1016207PD, 1016207RB
19205 1
 
19205 1 GASKET
1006201PD, 1006201RB, 1006201VB, 1006206, 1006211RD, 1008211RD, 1010207VB, 1016207PD, 1016207RB
9633
 
9633 GASKET
1006201DB, 1006201VB, 1016207PD, 1016207RB, 1016207SB, 10202014D, 1020201BC, 1020201DB, 1020201VB
Back to top