42999T Mercury GASKET


42999T GASKET Mercury 1200453EY, 1200453HY, 1225413EY, 1225423EY, 1225424EY, 1250424EY, 1250433EY, 1250434EY GASKET
42999T GASKET Mercury
Rating:
88

Buy GASKET 42999T Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 6
 

Mercury entire parts catalog list:

1200453EY 2006
1200453HY 2006
1225413EY 2007
1225423EY 2007
1225424EY 2007
1250424EY 2007,2009
1250433EY 2007
1250434EY 2007

Information:


This engine uses high voltage to control the fuel injectors.Disconnect electronic fuel injector enable circuit connector to prevent personal injury.Do not come in contact with the fuel injector terminals while the engine is running.
Note: Valve lash is measured between the rocker arm and the bridge for the inlet valves. Valve lash is measured between the rocker arm and the bridge for the exhaust valves. All of the clearance measurements and the adjustments must be made with the engine stopped. The valves must be fully closed.Valve Lash Check
An adjustment is not necessary if the measurement of the valve lash is in the acceptable range. Adjust the valve lash while the engine is stopped. The range is specified in Table 1.
Put the No. 1 piston at the top center position on the compression stroke. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston". To ensure cylinder No. 1 piston is at top center position compression stroke, both intake and exhaust valves on cylinder No. 1 will move freely. If the intake and exhaust valves do not move freely, cylinder No. 1 is on top center exhaust stroke. Install the timing pin in the flywheel.
Table 1
TDC No. 1 Compression Stroke Inlet Valves Exhaust Valves
Valve Lash 0.38 0.08 mm
(0.015 0.003 inch) 0.64 0.08 mm (0.025 0.003 inch)
Cylinders 1-2-4 1-3-5
Adjust the valve lash according to Table 1.
Lightly tap the rocker arm with a soft mallet. This action will ensure that the lifter roller seats against the base circle of the camshaft.
Loosen the adjustment locknut.
Place the appropriate feeler gauge between rocker arm and the valve bridge. Then, turn the adjustment screw in a clockwise direction. Slide the feeler gauge between the rocker arm and the valve bridge. Continue turning the adjustment screw until a slight drag is felt on the feeler gauge.
Tighten the adjustment locknut to a torque of 30 7 N m ((22 5 lb ft)). Do not allow the adjustment screw to turn while you are tightening the adjustment locknut. Recheck the valve lash after tightening the adjustment locknut. Remove the feeler gauge.
Remove the timing bolt and turn the flywheel by 360 degrees in direction of engine rotation. This will put the No. 6 piston at the top dead center position on the compression stroke. To ensure that cylinder No. 6 is at top dead center compression stroke, both intake and exhaust valves on cylinder No. 6 will move freely. If the intake and exhaust valves do not move freely, cylinder No. 6 is on top center exhaust stroke. Install the timing pin in the flywheel.
Table 2
TDC No. 6 Compression Stroke Inlet Valves Exhaust Valves
Valve Lash 0.38 0.08 mm
(0.015 0.003 inch) 0.64 0.08 mm (0.025 0.003 inch)
Cylinders 3-5-6 2-4-6
Adjust the valve lash according to Table 2.
Lightly tap the rocker arm with a soft mallet. The action will ensure that the lifter roller seats against the base circle of the camshaft.
Loosen the adjustment locknut.
Place the appropriate feeler gauge between rocker arm and the valve bridge. Then, turn the adjustment screw in a clockwise direction. Slide the feeler gauge between the rocker arm and the valve bridge. Continue turning the adjustment screw until a slight drag is felt on the feeler gauge.
Tighten the adjustment locknut to a torque of 30 7 N m ((22 5 lb ft)). Do not allow the adjustment screw to turn while you are tightening the adjustment locknut. Recheck the valve lash after tightening the adjustment locknut. Remove the feeler gauge.
If the engine is equipped with an engine compression brake, follow the procedure down below.
Table 3
TDC No. 6 Compression Stroke
Compression Brake Lash 0.9 0.2 mm (0.035 0.002 inch)
Cylinders 2-4-6
Adjust the compression brake lash according to Table 3.
Install the engine compression brake by referring to Disassembly and Assembly, "Compression Brake Remove and Install".
Begin setting lash on cylinder No. 6 top center compression stroke since engine was on this stroke from setting the engine valve lash.
Turn adjuster clockwise until there is contact with the exhaust valve bridge. Turn adjuster counterclockwise until the adjuster has turned two full rotations or until the rod is not in contact with the exhaust valve bridge ensuring that all the oil has left the cylinder. Install the feeler gauge with adjuster backed out at this time.
Use tooling in order to set brake lash of 0.9 0.2 mm (0.035 0.002 inch). The brake lash is measured


Parts gasket Mercury:

858935
 
858935 GASKET
1200453CD, 1200453HY, 1200473WD, 1200473YD, 1200D73AD, 1200D73CD, 1200D73HT, 1200E73HY, 1225412VD, 1225413ZD, 1225E73AD, 1225P73DD, 1225P73ED, 1225P73HD, 1225P83ED, 1226P73ED, 1250413CD, 1250413UE, 1250P73ED, 1250P73HD, 1250P83ED, 1251P73ED, 1256413W
850318 1
GASKET
850318 1 GASKET
1200453CD, 1200453EY, 1200453HY, 1200473VD, 1200473WD, 1200473YD, 1200D73AD, 1200D73CD, 1200D73ET, 1200D73HT, 1200E73EY, 1200E73HY, 1225413EY, 1225413ZD, 1225423EY, 1225424EY, 1225E73AD, 1225P73DD, 1225P73ED, 1225P73HD, 1225P83ED, 1226P73ED, 1250413C
804680
GASKET
804680 GASKET
1200453CD, 1200453EY, 1200453HY, 1200473WD, 1200473YD, 1200D73AD, 1200D73CD, 1200D73ET, 1200D73HT, 1200E73EY, 1200E73HY, 1225413EY, 1225413ZD, 1225423EY, 1225424EY, 1225E73AD, 1250413CD, 1250424EY, 1250433EY, 1250434EY
832934A00
 
832934A00 GASKET SET, Powerhead
1200453CD, 1200453EY, 1200453HY, 1200473WD, 1200473YD, 1200D73AD, 1200D73CD, 1200D73ET, 1200D73HT, 1200E73EY, 1200E73HY, 1225413EY, 1225413ZD, 1225423EY, 1225424EY, 1225E73AD, 1250413CD, 1250424EY, 1250433EY, 1250434EY
883252
GASKET
883252 GASKET
111047JHD, 1135D73CD, 1135D73FT, 1150413CD, 1150413FY, 1150413HF, 1150413HY, 1150413ZD, 1150423FG, 1150423FY, 1150423HF, 1150423HG, 1150423HY, 1150424FY, 1150424HY, 1150P73HY, 1175P73HY, 1200413FY, 1200413HY, 1200423FG, 1200423FY, 1200423HG, 1200423H
88907003
 
88907003 GASKET
1200453CD, 1200453EY, 1200453HY, 1200D73CD, 1200D73ET, 1200D73HT, 1200E73EY, 1200E73HY, 1225413EY, 1225423EY, 1225424EY, 1225E73AD, 1225P73DD, 1225P73ED, 1225P73HD, 1225P83ED, 1226P73ED, 1250413CD, 1250424EY, 1250433EY, 1250434EY, 1250P73ED, 1250P73H
889246A97
 
889246A97 GASKET KIT
1200453EY, 1200453HY, 1200D73ET, 1200D73HT, 1200E73EY, 1200E73HY, 1225413EY, 1225423EY, 1225424EY, 1225P73ED, 1225P73HD, 1225P83ED, 1226P73ED, 1250424EY, 1250433EY, 1250434EY, 1250P73ED, 1250P73HD, 1250P83ED, 1251P73ED
832933006
GASKET
832933006 GASKET
1200453EY, 1200D73ET, 1200E73EY, 1225413EY, 1225423EY, 1225424EY, 1225P73ED, 1225P73HD, 1225P83ED, 1226P73ED, 1250424EY, 1250433EY, 1250434EY, 1250P73ED, 1250P73HD, 1250P83ED, 1251P73ED, 192647GHD, 192847GHD
Back to top