52893A 2 Mercury GASKET SET (MOTOR OVERHAUL)


52893A 2 GASKET SET (MOTOR OVERHAUL) Mercury 1800100 GASKET
52893A 2 GASKET SET (MOTOR OVERHAUL) Mercury
Rating:
33

Buy GASKET SET (MOTOR OVERHAUL) 52893A 2 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: -
 

Compatible models:

1800100   Mercury

Mercury entire parts catalog list:

1800100 1970,1971,1972

Information:


Table 1
Tools Needed    
Part Number     Part Name     Quantity    
1U-5470     Engine Pressure Group     1    
Illustration 1 g00293196
1U-5470 Engine Pressure Group Refer to Special Instruction, SEHS8907, "Using the 1U-5470 Engine Pressure Group " for the instructions that are needed to use the 1U-5470 Engine Pressure Group .
Inspect the engine air cleaner inlet and ducting in order to ensure that the passageway is not blocked or collapsed.
Inspect the engine air cleaner element. Replace a dirty engine air cleaner element with a clean engine air cleaner element.
Check for dirt tracks on the clean side of the engine air cleaner element. If dirt tracks are observed, contaminants are flowing past the engine air cleaner element and/or the seal for the engine air cleaner element.
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool.
Making contact with a running engine can cause burns from hot parts and can cause injury from rotating parts.When working on an engine that is running, avoid contact with hot parts and rotating parts.
Use the differential pressure gauge of the 1U-5470 Engine Pressure Group .
Illustration 2 g00580368
(1) Air cleaner (2) Test location
Connect the vacuum port of the differential pressure gauge to test location (2). Test location (2) can be located anywhere along the air inlet piping after the engine air cleaner but before the turbocharger.
Leave the pressure port of the differential pressure gauge open to the atmosphere.
Start the engine. Run the engine in the no-load condition at high idle.
Record the value.
Multiply the value from Step 4.d by 1.8.
Compare the result from Step 4.e to the appropriate values that follow.The air flow through a used engine air cleaner may have a restriction. The air flow through a plugged engine air cleaner will be restricted to some magnitude. In either case, the restriction must not be more than the following amount: Maximum restriction ... 7.5 kPa (30 inch of H2O)The air flow through a new engine air cleaner element must not have a restriction of more than the following amount: Maximum restriction ... 3.0 kPa (12 inch of H2O)Exhaust Restriction
Back pressure is the difference in the pressure between the exhaust at the outlet elbow and the atmospheric air.
Table 2
Tools Needed    
Part Number     Part Name     Quantity    
1U-5470     Engine Pressure Group     1    
Illustration 3 g00293196
1U-5470 Engine Pressure Group Refer to Special Instruction, SEHS8907, "Using the 1U-5470 Engine Pressure Group " for the instructions that are needed to use the 1U-5470 Engine Pressure Group.
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool.
Making contact with a running engine can cause burns from hot parts and can cause injury from rotating parts.When working on an engine that is running, avoid contact with hot parts and rotating parts.
Use the differential pressure gauge of the 1U-5470 Engine Pressure Group in order to measure back pressure from the exhaust. Use the following procedure in order to measure back pressure from the exhaust:
Illustration 4 g00583322
(1) Muffler (2) Test location
Connect the pressure port of the differential pressure gauge to test location (2). Test location (2) can be located anywhere along the exhaust piping after the turbocharger but before the muffler.
Leave the vacuum port of the differential pressure gauge open to the atmosphere.
Start the engine. Run the engine in the no-load condition at high idle.
Record the value.
Multiply the value from Step 4 by 1.8.
Compare the result from Step 5 to the value that follows.


Parts gasket Mercury:

3523
 
3523 GASKET AND PACKING SET (1 PER CARBURETOR)
1115100, 1115503, 1115525, 1135100, 1150503, 1150625, 1400100, 1402202, 1800100, 1850503
48164
 
48164 GASKET, CARBURETOR FLANGE
1035204, 1040200, 1040208, 1090520, 1090528, 1115100, 1115503, 1115520, 1115523, 1115525, 1115528, 1135100, 1140520, 1140528, 1140629, 1150503, 1150538, 1150625, 1400100, 1402202, 1402205, 1650502, 1650503, 1800100, 1850503
48801
32434
 
32434 GASKET, UPPER - FACE PLATE TO WATER PUMP BODY
1080500, 1080508, 1090520, 1090528, 1115100, 1115503, 1115520, 1115523, 1115525, 1115528, 1135100, 1140520, 1140528, 1140629, 1150503, 1150538, 1150625, 1225620, 1650100, 1800100, 1850503, 1850506
Back to top