815087 Mercury GASKET


815087 GASKET Mercury 1002201FM, 1002201JK, 1002201VB, 1003201NK, 1004201JK GASKET
815087 GASKET Mercury
Rating:
18

Buy GASKET 815087 Mercury genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$34.13
 

08-06-2023

-: -
Technical Precision Replacement for EZGO/Cushman/TEXTRON 815087 Battery
Replacement For EZGO / CUSHMAN / TEXTRON 815087 || Unit per sale:1
Number on catalog scheme: 15
 

Compatible models:

Mercury entire parts catalog list:

1002201FM 2006
1002201JK 1990,1991,1992,1993,1994,1995,1996,1997,1998
1002201VB 1999,2000,2001,2002,2003,2004,2005
1003201NK 1993,1994,1996,1997,1998
1004201JK 1990,1991,1992,1993,1994,1995,1996,1997,1998

Information:


When any servicing or repair of the engine cooling system is performed, the procedure must be performed with the engine on level ground. This procedure will allow you to check accurately the coolant level. This procedure will also help in avoiding the risk of introducing an air lock into the coolant system.
Drain
Pressurized System: Hot coolant can cause serious burns. To open the cooling system filler cap, stop the engine and wait until the cooling system components are cool. Loosen the cooling system pressure cap slowly in order to relieve the pressure.
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap.
Illustration 1 g03423123
Typical example
Open the drain cock or remove the drain plug (1) on the engine. Also remove the drain plug (2). Open the drain cock or remove the drain plug on the radiator. Allow the coolant to drain.
Dispose of used engine coolant properly or recycle. Various methods have been proposed to reclaim used coolant for reuse in engine cooling systems. The full distillation procedure is the only method acceptable by Caterpillar to reclaim the used coolant.
For information regarding the disposal and the recycling of used coolant, consult your Caterpillar dealer or consult Dealer Service Tools.Flush
Flush the cooling system with clean water in order to remove any debris.
Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs and tighten to a torque of 35 N m (25 lb ft).
Do not fill the cooling system faster than 5 L (1.3 US gal) per minute to avoid air locks.Cooling system air locks may result in engine damage.
Fill the cooling system with clean water. Install the cooling system filler cap.
Start and run the engine at low idle until the temperature reaches 49 to 66 °C (120 to 150 °F).
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap. Open the drain valve (if equipped) or remove the cooling system drain plugs. Allow the water to drain. Flush the cooling system with clean water.
Close the drain valve (if equipped). Remove the old O ring seals from the drain plugs and clean the drain plugs. Install new O ring seal to the drain plugs. Install the drain plugs and tighten to a torque of 35 N m (25 lb ft). Fill
Do not fill the cooling system faster than 5 L (1.3 US gal) per minute to avoid air locks.Cooling system air locks may result in engine damage.
Fill the cooling system with Extended Life Coolant (ELC). Refer to this Operation and Maintenance Manual, "Refill Capacities and Recommendations" topic (Maintenance Section) for more information on cooling system specifications. Do not install the cooling system filler cap.
Start and run the engine at low idle. Increase the engine rpm to high idle. Operate the engine in order to open the engine thermostat. This operation will allow any air in the system to be purged. Decrease the engine speed to low idle. Stop the engine.
Maintain the coolant level at the maximum mark that is correct for your application.
Clean the cooling system filler cap. Inspect the gasket that is on the cooling system filler cap. If the gasket that is on the cooling system filler cap is damaged, discard the old cooling system filler cap. Install a new cooling system filler cap. If the gasket that is on the cooling system filler cap is not damaged, use a 9S-8140 Pressurizing Pump in order to pressure test the cooling system filler cap. The correct pressure for the cooling system filler cap is stamped on the face of the cooling system filler cap. If the cooling system filler cap does not retain the correct pressure, install a new cooling system filler cap.
Start the engine. Inspect the cooling system for leaks and for proper operating temperature.


Parts gasket Mercury:

95324
 
95324 GASKET, FLOAT BOWL
1002201FM, 1002201JK, 1002201VB, 1002204, 1003201NK
95326
 
95326 GASKET, DRAIN SCREW
1002201FM, 1002201JK, 1002201VB, 1002204, 1003201NK
95336
 
95336 GASKET, LEVER SCREW
1002201FM, 1002201JK, 1002201VB, 1002204, 1003201NK
812939
GASKET, CYLINDER HEAD
812939 GASKET, CYLINDER HEAD
1004137, 1004201FB, 1004201JK, 1004201VB
16115
 
16115 GASKET, DRIVESHAFTG HOUSING
1004137, 1004201FB, 1004201JK, 1004201VB
16164
 
16164 GASKET, LOWER WATER PUMP HOUSING
1004137, 1004201JK, 1004201VB, 1F04201WB
16160
 
16160 GASKET, WATER PUMP HOUSING PLATE
1004137, 1004201JK, 1004201VB, 1F04201WB
16158
 
16158 GASKET, WATER PUMP HOUSING
1004137, 1004201JK, 1004201VB, 1F04201WB
Back to top