85492 4 Mercury GASKET-BAFFLE PLATE TO EXHAUST COVER


85492 4 GASKET-BAFFLE PLATE TO EXHAUST COVER Mercury 10402139D GASKET
85492 4 GASKET-BAFFLE PLATE TO EXHAUST COVER Mercury
Rating:
83

Buy GASKET-BAFFLE PLATE TO EXHAUST COVER 85492 4 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 17
 

Compatible models:

10402139D   Mercury

Mercury entire parts catalog list:

10402139D 1989,1990,1991,1992,1993,1994,1995,1996,1997

Information:


Illustration 1 g00316188
Left Side Of Engine (Typical Example) (1) Covers. (2) Covers.Covers (1) allow access to the camshaft, the valve lifters, and the fuel control shaft. Covers (2) allow access to the crankshaft connecting rods, main bearings, and piston cooling jets. When the covers are removed, all the openings can be used for inspection and service.Pistons, Rings And Connecting Rods
The aluminum pistons have an iron band for the top two rings. This band helps reduce wear on the compression ring grooves. A chamber is cast into the piston just behind the top ring grooves. Oil from the piston cooling jets flows through this chamber in order to cool the piston. The flow of oil from the piston cooling jets also improves the life of the ring. The pistons have three rings which include two compression rings and one oil ring. All the rings are located above the piston pin bore. The oil ring is a standard ring. Oil returns to the crankcase through holes in the oil ring groove. The top two rings are the Keystone rings, which are tapered. The action of the ring in the piston groove, which is also tapered, helps prevent seizure of the rings from too much carbon deposit.The connecting rod has a taper on the pin bore end. This taper gives the rod and the piston more strength in the areas with the most load. Four bolts, which are set at a small angle, hold the rod cap to the rod. This design keeps the rod width to a minimum, so that a larger rod bearing can be used and the rod can still be removed through the liner.Crankshaft
The crankshaft changes the combustion forces in the cylinder into usable rotating torque which powers the machine. A vibration damper is used at the front of the crankshaft in order to reduce torsional vibrations (twist) that can cause damage to the engine.The crankshaft drives a group of gears on the front and the rear of the engine. The gear group on the front of the engine drives the oil pump, the jacket water pump, the fuel transfer pump, and the accessory drives.The rear gear group, which is also driven by the crankshaft, drives the camshafts and the accessory drives.Seals and wear sleeves are used at both ends of the crankshaft. The seals and wear sleeves are used for easy replacement and reduction of maintenance cost. Pressure oil is supplied to all main bearings through drilled holes in the webs of the cylinder block. The oil then flows through drilled holes in the crankshaft in order to provide oil to the connecting rod bearings. The 3508 crankshaft is held in place by five main bearings. The 3512 crankshaft is held in place by seven main bearings. The 3516 crankshaft is held in place by nine main bearings. A thrust plate at either side of the center main bearing controls the end play of the crankshaft.Camshaft
There is one camshaft per side. The 3508 camshaft is supported by five bearings. The 3512 camshaft is supported by seven bearings. The 3516 camshaft is supported by nine bearings. Each camshaft is driven by the gears at the rear of the engine.As the camshaft turns, each lobe moves a lifter assembly. There are three lifter assemblies for each cylinder. Each outside lifter assembly moves a pushrod and two valves. The valves can be inlet valves or exhaust valves. The center lifter assembly moves a pushrod that operates the unit injector. The camshafts must be in time with the crankshaft. The relation of the camshaft lobes to the crankshaft position causes the valves and unit injectors in each cylinder to operate at the correct time.


Parts gasket Mercury:

98769 1
 
98769 1 GASKET, BASE
1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 10402139D, 1040213YL, 1041312UB, 10432037D, 1043203DD, 1043203VD, 1043213DD, 1043302DD, 1043411DD, 1043412DB, 1043412DD, 1045217, 1050302DB, 1050302FB, 1050302FD, 1050302SD, 1050312FB, 1050312LD,
79797 1
 
79797 1 GASKET, HOUSING
1035207, 10402139D, 1045217
38501 1
 
38501 1 GASKET
1035207, 10402139D, 1045217, 1050312BC
75791 1
GASKET, Carburetor Flange
75791 1 GASKET, Carburetor Flange
1020201BC, 10402139D, 1045217
9651
 
9651 GASKET SET
10402139D, 1045217
27936 1
79650 1
 
79650 1 GASKET, Powerhead
10402139D, 1045217
Back to top