96278 Mercury GASKET


96278 GASKET Mercury 1135726, 1150625, 1150628, 1175626, 1200628 GASKET
96278 GASKET Mercury
Rating:
8

Buy GASKET 96278 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 2
 

Compatible models:

Mercury entire parts catalog list:

1135726 1986,1987,1988
1150625 1985
1150628 1978,1979,1980,1982,1983,1984,1985
1175626 1976,1977,1978,1979,1980,1985,1986,1988
1200628 1978,1979,1980,1982,1983,1984,1985,1986,1987,1988

Information:


Table 1
Diagnostic Codes Table
Description Conditions which Generate this Code System Response
444-5 Starter Motor Relay current below normal The Electronic Control Module (ECM) detects an open circuit and/or a short to the +Battery in the start relay. The ECM can only detect this condition when the start relay is not energized. The code is logged.
444-6 Starter Motor Relay current above normal The ECM detects a short circuit to ground in the start relay. The ECM can only detect this condition when the start relay is energized. The ECM has the ability to crank the engine when the Engine Control Switch (ECS) is placed in the START position. After the ECS is placed in the START position, the ECM will begin the prelube cycle. The ECM will send an engine start signal to terminal BH of the customer connector after the prelube cycle is complete. The customer's engine start signal will return on terminal BJ of the customer connector. The signal is then sent to terminal 10 of the G-C6 connector on the "Marine Power Display (MPD)" panel.If a "Starter Select Switch" is installed in the MPD panel, the switch can be set to use either the electric starting motors or the air starting motors. If electric starting motors are installed on the engine, the starting motor relays "SMMS1" and "SMMS2" will be energized. If air starting motors are installed on the engine, the air start solenoids will be energized. If a "Starter Select Switch" is not installed in the MPD panel, the start signal is routed from TB-8 to TB-7. The signal from TB-7 is wired to the starting system. The crank cycle will continue for the time that is equal to the cycle crank time that has been programmed or the crank cycle will continue until the engine speed reaches the crank terminate speed.Note: The prelube cycle can be disabled by setting the duration of the prelube cycle to 0.This process will repeat for a programmed amount of times "Total Number of Crank Cycles". If the engine does not start, Caterpillar Electronic Technician (ET) will display "OVERCRANK". The engine control will be in an idle state. The process can be restarted by turning the ECS to the OFF/RESET position. Next, turn the ECS to the STOP position. Then turn the ECS to the START position.The engine can be manually started by using the "crank override switch" which is located on the in


Parts gasket Mercury:

66101
 
66101 GASKET, POWERHEAD TO EXHAUST EXTENSION PLATE
1115503, 1115525, 1150503, 1150625, 1850503
87775
 
87775 GASKET, INLET COVER
1035204, 1045217, 1050200, 1060504, 1070500, 1080500, 1090520, 1115520, 1115523, 1140520, 1150625, 1150628, 1175626, 1200628, 1225620, 1250422GD, 1300623, 192847GHD
6452
 
6452 GASKET AND PACKING SET
1135412GD, 1135726, 1150453BD, 1150453GD, 1150453JD, 1150625, 1150628, 1175412GD, 1175626, 1200412GD, 1200628, 1225620
67274 1
 
67274 1 GASKET
1135412GD, 1150453GD, 1150453JD, 1150625, 1150628, 1175412GD, 1175626, 1200628
99173 2
 
99173 2 GASKET
11354120D, 1135412MD, 1135412SD, 1135412VD, 1135473UD, 1135473VD, 1150413SD, 1150413VD, 1150453JD, 1150625, 1150628, 1175413LD, 1175413MD, 1175626
99177 2
 
99177 2 GASKET
1150625, 1150628, 1175626, 1200412GD, 1200628
90484A88
GASKET SET
90484A88 GASKET SET
1135412GD, 1135726, 1150625, 1150628
12775 4
 
12775 4 GASKET
1200628
Back to top