14170A 1 Mercury HANDLE ASSEMBLY,THROTTLE


14170A 1 HANDLE ASSEMBLY,THROTTLE Mercury 1018204 HANDLE
14170A 1 HANDLE ASSEMBLY,THROTTLE Mercury
Rating:
73

Buy HANDLE ASSEMBLY,THROTTLE 14170A 1 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 4
 

Compatible models:

1018204   Mercury

Mercury entire parts catalog list:

1018204 1984,1985,1986,1987

Information:


Illustration 1 g02352096
Illustration 2 g02355179
Table 1
SPECIFICATIONS FOR 342-6646 Piston and Rod    
Callout     Part Number     Part Name     Specification Description    
-     -     -     Apply clean engine oil to the pistons, the piston rings, and the cylinder bore.
Position the piston rings so that the end gaps are located 120 degrees from each other.
Ensure that the proper piston and connecting rod are in the corresponding cylinder with the bearing retainer notch toward the right side of the engine.    
1     160-8197     Bolt     Apply 4C-5593 Thread Lubricant to the threads
Torque to.........................
50 5 N m (37 4 lb ft)
Place an index mark on each bolt.
Torque an additional 90° 5° (1/4 turn).    
4     269-7290     Connecting Rod Bearing     Apply clean engine oil to the upper and lower halves before installation. Endure that the gearing tab comes in contact with the slot in the connecting rod.
Etch the cylinder number on the connecting rod and the cap. Mark the connecting rod and the cap with a number 1 through 6. Mark the numbers on the same side of the connecting rod as the bearing retainer notch.
Install with the part number of the forging for the rod assembly to the rear of the engine. The rear of the engine is the flywheel end of the engine. Lubricate the rod and piston group with clean engine oil before you insert the rod and piston group into the block.    
A     -     -     Bore in the connecting rod for the sleeve bearing.......
54.630 0.013 mm (2.1508 0.0005 inch)    
B     -     -     Bore in the bearing for the piston pin.......
50.035 0.008 mm (1.9699 0.0003 inch)    
C     -     -     The connecting rod may be heated from
175 to 260 °C (347 to 500 °F) for the installation of the sleeve bearing. Maximum distance for heating the connecting rod....
85 mm (3.3 inch)
Thoroughly lubricate the piston pin with clean engine oil prior to assembly of the piston and connecting rod.    
D     -     -     The bearing joint must be within 5° of either location.    
E     -     -     Distance between the center of the bearings.......
217 mm (8.5 inch)    
F     -     -     Bore in the connecting rod for the crankshaft bearing.......
85.000 0.013 mm (3.3464 0.0005 inch)    Specifications
Illustration 3 g02352110
Note: Callouts in Table 2 refer to the Assembly Procedure.
Table 2
SPECIFICATIONS FOR 342-6646 Piston and Rod    
Callout     Part Number     Part Name     Specification Description    
4     262-2888
262-2891
300-1319     Piston Ring     Position the spring for the oil control ring in the oil ring groove in the piston body assembly.
Position the oil control ring over the spring. Position the oil control ring so that the gap is 180° from the joint in the spring. Use 4C-3601 Piston Ring Expander to install the oil control ring on the piston.
Use 4C-3601 Piston Ring Expander to install the intermediate piston ring with the side that has the identification "UP-2" toward the top of the piston.
Use 4C-3601 Piston Ring Expander to install the top piston ring with the side that has the identification "UP-1" toward the top of the piston.
Position piston rings (4) so the gaps are 120° from each other.    Removal Procedure
Table 3
Required Tools    
Tool     Part Number     Part Description     Qty    
A     363-4046     Piston Ring Compressor     1    
B     4C-5593     Anti-Seize Compound     1    Start By:
Remove the cylinder head.
Remove the engine oil pump.
Remove the piston cooling jets.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.


Parts handle Mercury:

85174A 1
 
85174A 1 HANDLE ASSEMBLY, STARTER ROPE
1006201DB, 1006201PD, 1006201RB, 1006201VB, 1006206, 1006211RD, 1008211RD, 1010207VB, 1011201DB, 1016207PD, 1016207RB, 1016207SB, 1018200, 1018204, 10202014D, 1020201BC, 1020201DB, 1020201VB, 1025200, 1031203PD, 1031203UB, 1031203UD, 1031207ZF, 10313
41042
 
41042 HANDLE, CARRYING
1018204, 10202014D, 1020201BC, 1020201DB, 1020201VB, 1F10203VD, 1F10352VD, 1F13203FB, 1F15201UD
42330 1
 
42330 1 HANDLE, SHIFT
1018204, 1020201BC
Back to top