70671A 1 HARNESS ASSEMBLY, STOP SWITCH Mercury
1004200, 1040206
HARNESS
Price: query
Rating:
Number on catalog scheme: 7A
Mercury entire parts catalog list:
- STEERING HANDLE ASSEMBLY » 70671A 1
- STEERING HANDLE ASSEMBLY » 70671A 1
Information:
Start By:
Remove the engine enclosure. Refer to Disassembly and Assembly, "Engine Enclosure (Hood) - Remove and Install" for the proper removal procedure.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contamination of the hydraulic system with foreign material will reduce the service life of the hydraulic system components.To prevent contaminants from entering the hydraulic system, always plug or cap the lines, fittings, or hoses as they are disconnected. Cover any disassembled components and clean them properly before assembly.Clean the hydraulic system properly after any major component exchange or especially after a component failure, to remove any contamination.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, all hoses and all tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Drain the hydraulic oil from the hydraulic oil tank. The capacity of the hydraulic oil tank is approximately 75.5 L (19.9 US gal). Refer to Operation and Maintenance Manual, "Hydraulic System Oil - Change" for the proper draining procedure.
Illustration 1 g01061201
Disconnect harness assembly (2) from the backup alarm (1). Remove the cable straps that secure the harness assembly to the grill. Position the harness assembly out of the way.
Illustration 2 g01061230
Illustration 3 g01061207
Remove clamps (3) and (4) .
Illustration 4 g01061209
Attach a suitable lifting device to radiator guard (5). Remove bolts (6) that secure radiator guard (5) to the machine frame, and remove the radiator guard and the grill as a unit. The weight of the radiator guard and grill as a unit is approximately 70 kg (154 lb).
Illustration 5 g01057319
Loosen clamps (8) and (12). Remove hoses (10) from hydraulic oil cooler (9) .
Remove bolts (11) that secure the bottom of the hydraulic oil cooler to the radiator bracket.
Support the hydraulic oil cooler. Remove remaining bolts (7) that secure hydraulic oil cooler (9) to the radiator bracket. Remove the hydraulic oil cooler.Installation Procedure
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 6 g01057319
Position hydraulic oil cooler (9) on the radiator bracket. Install the top bolts (7) .
Install bolts (11) that secure the bottom of the hydraulic oil cooler to the radiator bracket.
Install hoses (10) on hydraulic oil cooler (9) and tighten clamps (8) and (12) .
Illustration 7 g01061209
Attach a suitable lifting device to radiator guard (5). Position the radiator guard and the grill as a unit. Install bolts (6). The weight of the radiator guard and grill as a unit is approximately 70 kg (154 lb).
Remove the engine enclosure. Refer to Disassembly and Assembly, "Engine Enclosure (Hood) - Remove and Install" for the proper removal procedure.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contamination of the hydraulic system with foreign material will reduce the service life of the hydraulic system components.To prevent contaminants from entering the hydraulic system, always plug or cap the lines, fittings, or hoses as they are disconnected. Cover any disassembled components and clean them properly before assembly.Clean the hydraulic system properly after any major component exchange or especially after a component failure, to remove any contamination.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, all hoses and all tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Drain the hydraulic oil from the hydraulic oil tank. The capacity of the hydraulic oil tank is approximately 75.5 L (19.9 US gal). Refer to Operation and Maintenance Manual, "Hydraulic System Oil - Change" for the proper draining procedure.
Illustration 1 g01061201
Disconnect harness assembly (2) from the backup alarm (1). Remove the cable straps that secure the harness assembly to the grill. Position the harness assembly out of the way.
Illustration 2 g01061230
Illustration 3 g01061207
Remove clamps (3) and (4) .
Illustration 4 g01061209
Attach a suitable lifting device to radiator guard (5). Remove bolts (6) that secure radiator guard (5) to the machine frame, and remove the radiator guard and the grill as a unit. The weight of the radiator guard and grill as a unit is approximately 70 kg (154 lb).
Illustration 5 g01057319
Loosen clamps (8) and (12). Remove hoses (10) from hydraulic oil cooler (9) .
Remove bolts (11) that secure the bottom of the hydraulic oil cooler to the radiator bracket.
Support the hydraulic oil cooler. Remove remaining bolts (7) that secure hydraulic oil cooler (9) to the radiator bracket. Remove the hydraulic oil cooler.Installation Procedure
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 6 g01057319
Position hydraulic oil cooler (9) on the radiator bracket. Install the top bolts (7) .
Install bolts (11) that secure the bottom of the hydraulic oil cooler to the radiator bracket.
Install hoses (10) on hydraulic oil cooler (9) and tighten clamps (8) and (12) .
Illustration 7 g01061209
Attach a suitable lifting device to radiator guard (5). Position the radiator guard and the grill as a unit. Install bolts (6). The weight of the radiator guard and grill as a unit is approximately 70 kg (154 lb).