889611K02 Mercury HARNESS KIT, Accessory Power (30 Feet)


889611K02 HARNESS KIT, Accessory Power (30 Feet) Mercury 1135V13FB, 1135V13HB, 1200V13FB, 1200V13HB HARNESS
889611K02 HARNESS KIT, Accessory Power (30 Feet) Mercury
Rating:
93

Buy HARNESS KIT, Accessory Power (30 Feet) 889611K02 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: -
 

Compatible models:

Mercury entire parts catalog list:

1135V13FB 2006
1135V13HB 2006
1200V13FB 2006
1200V13HB 2006

Information:


Illustration 1 g01027829
Schematic
Test Step 1. Inspect Electrical Connectors and Wiring
Remove electrical power from the engine ECM.
Illustration 2 g01310457
Left side engine view (typical example)
(1) J2/P2 ECM connectors
Illustration 3 g01161069
Typical location of the fuel filter differential pressure switch
(2) Fuel filter differential pressure switch
Thoroughly inspect connector (1). Also, thoroughly inspect the connector for switch (2). Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Illustration 4 g01027831
P2 ECM connector
(P2-65) Fuel filter differential pressure switch
(P2-83) Return for the switch
Illustration 5 g01160725
Connector for the fuel filter differential pressure switch
(Terminal 1) Fuel filter differential pressure switch
(Terminal 2) Return for the switch
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector and the sensor connectors that are associated with the active diagnostic code.
Check the ECM connector (allen head screw) for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Check the harness and wiring for abrasions and for pinch points from the sensors back to the ECM. Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted. The harness and wiring are free of corrosion, of abrasion, and of pinch points.Results:
OK - The harness and wiring are OK. Proceed to Test Step 2.
Not OK - There is a problem in the connectors and/or wiring.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.Verify that the repair eliminates the problem.STOPTest Step 2. Check the Switch Circuit
Disconnect the connector for the differential pressure switch.
Check continuity between the terminals for the differential pressure switch at the connector. Expected Result:The resistance check indicates a short circuit.Results:
OK - The resistance check indicates a short circuit. The differential pressure switch is OK. Proceed to Test Step 3.
Not OK - The resistance check indicates an open circuit. There is an open circuit in the wiring for the fuel filter differential pressure switch.Repair: Replace the differential pressure switch.STOPTest Step 3. Check the Wiring between the Connector for the Differential Pressure Switch and the ECM
Disconnect the J2/P2 ECM connector.
Create a short between the terminals of the connector for the differential pressure switch.
Check continuity at the ECM connector between terminal P2-65 (fuel filter pressure switch) and terminal P2-83 (switch return). Expected Result:The resistance check indicates a short circuit.Results:
OK - The resistance check indicates a short circuit.Repair: Check all connectors and wiring. Ensure that there are clean, solid connections at each connector. Return all wiring to the original configuration and retest the circuit. The most likely cause of the problem is a poor connection. The next most likely cause of the problem is the differential pressure switch. The least likely cause of the problem is the ECM. The ECM can be tested by creating a short between the ECM terminals for the differential pressure switch. Start and run the engine. After an hour, check for a E390 event code. If the event code is activated with the short in place at the ECM connector, replace the ECM. Refer to Troubleshooting, "ECM - Replace". Verify that the problem is resolved.STOP
Not OK - The resistance check indicates an open circuit.Repair: Repair the connectors or wiring and/or replace the connectors or wiring between the ECM and the connector for the differential pressure switch.STOP


Parts harness Mercury:

888416T03
 
888416T03 HARNESS ASSEMBLY
1135V13ED, 1135V13FB, 1135V13HB, 1200E73EY, 1200E73HY, 1200V13ED, 1200V13ER, 1200V13FB, 1200V13HB, 1200V23ED, 1200V23ER, 1225E73AD, 1225V13EB, 1225V13EF, 1225V23ED, 1225V33EB, 1250V23EF, 1250V34EB, 1275V23ER, 1275V24EB, 1275V34EB, 1300V23EB, 1300V24E
819514A20
 
819514A20 HARNESS ASSEMBLY, Trim
1200V13DD, 1200V13ED, 1200V13ER, 1200V13FB, 1200V13HB, 1200V23ED, 1200V23ER, 1225V13EB, 1225V13EF, 1225V23ED, 1225V33EB, 1250V23EF, 1250V34EB, 1275V23ER, 1275V24EB, 1275V34EB, 1300V23EB, 1300V24EF, 1300V24KD, 1300V33EB, 1301V23KD, 1301V33KD
880596514
 
880596514 HARNESS ASSEMBLY
1200V13DD, 1200V13ED, 1200V13ER, 1200V13FB, 1200V13HB, 1200V23ED, 1200V23ER, 1225V13EB, 1225V13EF, 1225V23ED, 1225V33EB, 1250V23EF, 1250V34EB, 1275V23ER, 1275V24EB, 1275V34EB, 1300V23EB, 1300V24EF, 1300V24KD, 1300V33EB, 1301V23KD, 1301V33KD
819514A23
 
819514A23 HARNESS ASSEMBLY, Trim
1135V13ED, 1135V13FB, 1135V13HB
892137T03
HARNESS ASSEMBLY, Fuse
892137T03 HARNESS ASSEMBLY, Fuse
1135V13ED, 1135V13FB, 1135V13HB
854010 1
 
854010 1 HARNESS ASSEMBLY
1135V13ED, 1135V13HB
822560A13
 
822560A13 HARNESS ASSEMBLY, Diagnostic Tester
1135V13ED, 1135V13FB, 1135V13HB
Back to top