96220A 4 Mercury HARNESS


96220A 4 HARNESS Mercury 11354120D, 1135726, 1150453BD, 1150453JD, 1150625, 1150628, 1175626, 1200412GD, 1200628 HARNESS
96220A 4 HARNESS Mercury
Rating:
28

Buy HARNESS 96220A 4 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 20
 

Mercury entire parts catalog list:

11354120D 1990,1991
1135726 1986,1987,1988
1150453BD 1988
1150453JD 1990
1150625 1985
1150628 1978,1979,1980,1982,1983,1984,1985
1175626 1976,1977,1978,1979,1980,1985,1986,1988
1200412GD 1989,1990
1200628 1978,1979,1980,1982,1983,1984,1985,1986,1987,1988

Information:


Table 1
Diagnostic Trouble Codes for the Data Link Configuration Status
J1939 Code CDL Code Code Description
(code descriptions may vary) Comments
- 1603-14 Machine Control Module: Special Instruction The data from a machine ECM is not in the correct format.
The code is logged.
639-14 247-14 J1939 Network #1 : Special Instruction The data received from the CAN A data bus is not in the correct format.
The code is logged.
1231-14 2348-14 J1939 Network #2 : Special Instruction The data received from the CAN B data bus is not in the correct format.
The code is logged.
5576-14 3468-14 Aftertreatment #1 Identification : Special Instruction The data received from the aftertreatment ID module is not in the correct format.
The code is logged. The diagnostic code for the special instruction is logged to report the configuration status of the data link. The diagnostic code for the special instruction does not check the physical condition of the data link.The following list identifies possible faults on the data link:
Incorrect personality module code
An invalid configuration parameter
Incorrect module or display on the data link
Damaged data link wiring
Incompatible software in one of the ECMsComplete the procedure in the order in which the steps are listed.
Table 2
Troubleshooting Test Steps Values Results
1. Check for an Associated -9 Code
A. Establish communication between the electronic service tool and the Electronic Control Module (ECM) for the engine.
B. Download a "Warranty Report" from the engine ECM before troubleshooting or clearing diagnostic trouble codes.
C. Check for active diagnostic codes.
Associated Trouble code
Result: An associated -9 code is logged.
Repair: Repair all associated -9 codes before continuing with this procedure. Refer to Troubleshooting, "CAN Data Link - Test".
If a -14 code is still present after resolving the -9 code, proceed to Test Step 2.
Result: An associated -9 code is not logged.
Proceed to Test Step 2.
2. Check the Personality Module Code for Compatibility with the Application
A. Connect to the electronic service tool.
B. Select the ECM connection that is related to the logged code.
C. Check if the personality module code is valid for the application.
Compatible personality module
Result: The code is valid for the application.
Proceed to Test Step 3.
Result: The code is not valid for the application.
Repair: Obtain the correct flash file and update the ECM. Reset all active codes and clear all logged codes. Return the unit to service.
3. Check that the Latest Available Software is Installed
A. Ensure that the latest software is installed on the engine ECM.
Ensure that the software installed is for the correct system voltage (12 V or 24 V).
If necessary, refer to Troubleshooting, "ECM Software - Install" for the correct procedure.
Software
Result: The latest software is not installed.
Repair: Install the latest software. If necessary, refer to Troubleshooting, "ECM Software - Install" for the correct procedure.
Turn the keyswitch to the ON position.
If the fault is cleared, return the engine to service.
If the fault is still present, proceed to Test Step 4.
Result: The latest software is installed. The software is for the correct system voltage.
Proceed to Test Step 4.
4. Check the Configuration Parameters
A. Check the configuration parameters to ensure that the parameters are programmed correctly. Refer to Troubleshooting, "Configuration Parameters".
B. Select the ECM connection that is related to the logged code.
Correct configuration parameters
Result: The configuration parameters are programmed correctly.
Proceed to Test Step 5.
Result: The configuration parameters are not programmed correctly.
Repair: Program the parameters to function with the other modules on the data link. Reset all active codes and clear all logged codes. Return the unit to service.
5. Check for Compatibility with Any Other ECM on the Data Link
A. Use the as shipped information found in SIS web TMI to determine if any other ECM or display on the data link are incompatible.
B. Select the ECM connection that is related to the logged code.
Compatible ECM
Result: The ECMs are not compatible.
Repair:Replace the incompatible ECM with the correct module. Reset all active codes and clear all logged codes. Return the unit to service.
If the procedure did not correct the fault, contact the Dealer Solutions Network (DSN).


Parts harness Mercury:

45341 20
 
45341 20 HARNESS, CONTROL PANEL (20 FEET)
1115100, 1115503, 1115525, 1150503, 1150625
69738A 7
 
69738A 7 HARNESS ASSEMBLY, COIL TO SWITCH BOX
1150625, 1150628, 1175626, 1200628
69739A 2
 
69739A 2 HARNESS, COIL TO SWITCH BOX
1135726, 1150453BD, 1150625, 1150628, 1175626, 1200628
68259A 1
 
68259A 1 HARNESS
1150625, 1150628, 1175626, 1200628
68260A 1
 
68260A 1 HARNESS
1150625, 1150628, 1175626, 1200628
86396A 8
 
86396A 8 HARNESS ASSEMBLY, Tachometer (5.00 Feet)
1070312BC, 1070717, 10754120D, 1090524, 1115525, 11354120D, 1135412GD, 1135726, 1150453BD, 1150453GD, 1150453JD, 1150625, 1150628, 1175412GD, 1175626, 1200412GD, 1200413GD, 1200628, 1220727, 1256413WD, 1300623
69739A 6
 
69739A 6 HARNESS ASSEMBLY
11354120D, 1135412GD, 1135412MD, 1135412SD, 1135412VD, 1150453GD, 1150453JD, 1175412GD, 1200412GD
96220A12
 
96220A12 HARNESS, ENGINE
11354120D, 1135412GD, 1150453GD, 1150453JD, 1175412GD, 1175413LD, 1200412GD
Back to top