30413 Mercury HOOK, COWL LATCH FASTENING


30413 HOOK, COWL LATCH FASTENING Mercury 1020100, 1020202, 1020208, 1035204, 1035207, 1040200, 1040208, 1045217, 1050200, 1075524, 1080500, 1080508, 1090520, 1090524, 1090528, 1115100, 1115503, 1115520, 1115523, 1115525, 1115528, 1135100, 1140520, 1140528, 1140629, 1150503, 1150538, 1150625 HOOK
30413 HOOK, COWL LATCH FASTENING Mercury
Rating:
103

Buy HOOK, COWL LATCH FASTENING 30413 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 12
 

Mercury entire parts catalog list:

1020100 1970
1020202 1972
1020208 1978,1979,1980
1035204 1984,1985,1986
1035207 1987,1988,1989
1040200 1980,1982,1983
1040208 1978,1979
1045217 1987,1988,1989
1050200 1980,1982,1983,1984,1985,1986
1075524 1984,1985,1986
1080500 1980,1982,1983
1080508 1978,1979
1090520 1980,1982,1983
1090524 1984,1985,1986,1987,1988
1090528 1978,1979
1115100 1970,1971,1972
1115503 1973,1974,1976,1977
1115520 1980,1982,1983
1115523 1973
1115525 1985
1115528 1978,1979
1135100 1970,1971
1140520 1980
1140528 1978,1979
1140629 1979
1150503 1973,1974,1975,1976,1977,1985
1150538 1978
1150625 1985
1200203 1973,1974,1975,1976,1977
1250422GD 1989,1990,1991,1992,1993,1994
1400100 1970,1971
1402202 1972,1973,1974
1402205 1975,1976,1977
1500100 1970
1500101 1971,1972,1973,1974
1500205 1975
1500206 1976,1977,1978,1979
1650100 1970,1971
1800100 1970,1971,1972
1850503 1973,1974,1975
1850506 1976,1977

Information:

start by:a) separation of governor from fuel injection pump housing1. Remove the fuel injection pumps as follows: a) Remove the protection cap and washer (1). b) Install tool (A) and remove bushing (2) from housing. c) Use tool (B) to lift the fuel injection pump out of the housing.d) Remove spacer (4) from the pump housing.
When injection pumps, spacers and lifters are removed from the injection pump housing, keep the parts of each pump together so they can be installed back in their original location.
2. Disassemble the fuel injection pumps as follows: a) Remove seal (3) from bonnet (5).b) Remove ring (6) to make a separation of bonnet (5) from barrel (9).c) Remove spring (7) and check valve (8) from bonnet (5).d) Remove the gear segment, plunger (10), washer (11) and spring (12) from barrel (9).
Be careful when the injection pumps are disassembled. Do not cause damage to the surface on the plunger. The plunger and barrel for each pump are made as a set. Do not put the plunger of one pump in the barrel of another pump. If one part has wear, install a complete new pump assembly. Be careful when the plunger is put into the bore of the barrel.
3. Remove rack (13) from the pump housing.4. Remove lifters (14) from the pump housing. 5. Remove the camshaft plate (15), bolt and lock. 6. Remove spring (16) and gear assembly (17) from the camshaft. 7. Remove camshaft (19) from the pump housing. 8. Remove the camshaft bearings from the fuel injection pump housing with tool (C).9. Remove the two bearings (18) from the fuel injection pump housing if necessary.Assemble Fuel Injection Pump Housing
1. Install the camshaft bearings in the fuel injection pump housing with tool (C). Install the bearing in governor end of housing so the lubrication hole in the bearing is in alignment with lubrication hole in housing. Install the camshaft bearings even with outside ends of fuel injection pump housing.
Install the rack bearing in the governor end of the housing with the small holes in the bearing parallel to the vertical centerline of the pump.
2. Install the rack bearing in the governor end of the housing with tooling (F). Install the bearing so it will be .195 .005 in. (4.95 0.13 mm) lower than the face of the housing.
Tooling (D) must be used to install the rack bearing in the accessory drive end of the housing. This will put the tab on the bearing in its correct position and install the bearing to the correct depth.
3. Install the rack bearing in the accessory drive end of the housing with tooling (D). 4. Put clean engine oil on camshaft. Install the camshaft in fuel injection pump housing. Put the governor drive gear (1) and spring (2) in position on the camshaft. Install the camshaft plate (3), bolt and lock. 5. Install lifters (4) in their correct positions in the housing. Put clean engine oil on the rack. Install rack (5) in the fuel injection pump housing with the opening in the rack near the governor end of the housing.6. Install the spacers in their respective positions in the housing. When new lifters and pumps are installed, it is necessary to make adjustment of the fuel pump timing. See FUEL INJECTION PUMP TIMING DIMENSIONS SETTING, OFF ENGINE in TESTING AND ADJUSTING.7. Assemble the fuel injection pumps as follows: a) Put clean fuel oil on all parts.b) Install the spring on the barrel.c) Install the washer on the plunger and gear segment. Install the plunger in the barrel.d) Install the spring and check valve in the bonnet.e) Put the bonnet in position on the barrel and install the ring to hold the unit together.f) Install the seal on the bonnet.
Make sure the fuel rack is in the center (zero) position before the fuel injection pumps are installed.
8. Put the rack in the center position with tooling (E) as follows: a) Install location fixture (6) on the fuel injection pump housing.b) Install the gauge (7). Move the gauge (7) to zero. Push the rack (5) against the gauge. c) Install the clamp (8) on pump housing as illustrated. This will keep the rack in the center when the fuel injection pumps are installed.9. With the rack in the center, install the fuel injection pumps as follows: a) Turn the camshaft until the lobe of the camshaft is down for the pump to be installed. b) Install tool (B) on the pump.c) Put the grooves (9) in the bonnet and barrel in alignment with the groove (10) in the pump gear segment. Put the pump in position so the grooves are in alignment with the guide pins in the housing bore. Install the pump in its correct position in the housing. d) Install bushing (11) over the bonnet. Install tool (B) on the bonnet and push down on tool (B). Tighten bushing (11) by hand until the bushing is even with top of housing. If installation of the bushing can not be made this far by hand, remove it. Remove the pump, put the parts in alignment again and install the bushing again.
If installation of pump is correct, the bushing can be tightened by hand until it is even with face of pump housing.
e) Make a check of the rack travel after each pump is installed as follows: Move clamp (8) away from the end of the rack. Use gauge (7) to measure the rack movement. The total rack movement must be .800 in. (20.32 mm). If the rack can not be moved this distance, the pump gear segment is not in the correct position and the pump must be removed and installed again. f) Remove tool (B) and tool (E). Install tool (A) and tighten the bushing to a torque of 150 10 lb.ft. (205 14 N m). Remove tool (A). Install the washers and protection caps for the fuel injection pumps.end by:a) connection of governor to fuel injection pump


Parts hook Mercury:

39482
 
39482 HOOK, FRONT COVER LATCH
1020100, 1400100, 1402202
55455
 
55455 HOOK, TOP COWL LATCH - REAR
1020208, 1035204, 1035207, 1040200, 1040208, 1045217, 1050200, 1075524, 1080500, 1080508, 1090520, 1090524, 1090528, 1115100, 1115503, 1115520, 1115523, 1115525, 1115528, 1135100, 1140520, 1140528, 1140629, 1150503, 1150538, 1150625, 1402205, 1500101
60866
 
60866 HOOK, FRONT COVER LATCH
1020202, 1200203, 1402205
61158T
 
61158T HOOK
1150625, 1150628, 1175626, 1200628, 1250422GD
87907
 
87907 HOOK
1135726, 1150453BD, 1150625, 1150628, 1175626, 1200628, 1220727, 1225620
Back to top