16247 Mercury HOSE, FUEL


16247 HOSE, FUEL Mercury 1004137, 1004201JK HOSE
16247 HOSE, FUEL Mercury
Rating:
33

Buy HOSE, FUEL 16247 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 22
 

Compatible models:

Mercury entire parts catalog list:

1004137 1987,1988,1989
1004201JK 1990,1991,1992,1993,1994,1995,1996,1997,1998

Information:

2. Remove bolts (2), elbows (1) and the gaskets from the raw water pump. 3. Remove nuts (4), raw water pump (3) and the gasket from the front timing gear cover.Install Raw Water Pump
1. Put the gasket and raw water pump (1) into position on the front timing gear cover and install the nuts that hold them. 2. Install the gasket, elbows (2) on the raw water pump with bolts (3).3. Fill the cooling system with coolant to the correct level. See the Operation & Maintenance Manual.Disassemble Raw Water Pump
Start By:a. remove raw water pump FLUID SPILLAGE CONTAINMENTCare must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to "TOOLS AND SHOP PRODUCT GUIDE, NENG2500", for tools and supplies suitable to collect and contain fluids in Caterpillar machines. Dispose fluids according to local regulations and mandates. 1. Remove screws (1) and cover assembly (2) from body assembly (3). 2. Remove plate (5) and gasket (4) from the cover assembly. 3. Remove seal (6) and impeller assembly (7) from the body assembly. Make a note of the direction of the impeller blades for correct assembly. 4. Remove seal (8) from the shaft. 5. Use Tool (A) and remove ring (10) from the shaft.6. Remove cover (9) (part of the seal assembly) from the body assembly. 7. Remove spring (11) (part of seal assembly) from the body assembly. 8. Remove carbon seal (12) (part of the seal assembly) from the body assembly. 9. Remove bolts (14) and remove housing (13) from body assembly (3). 10. Remove cam (15) and ceramic seal (16) (part of the seal assembly) from body assembly (3). 11. Remove plate (17) from the body assembly. 12. Remove seal (18) from the shaft. 13. Use Tool (B) and remove ring (19) from the housing. 14. Use a press and remove shaft (20) and the bearings from housing (13). 15. Use a press and Tool (C) to remove bearings (21) from shaft (20). 16. Remove seal (22) from housing (13).Assemble Raw Water Pump
1. Use Tooling (A) and install seal (1) in housing (2). Make sure the lip of the seal is toward the bearing bore as shown. Put 1P-0808 General Purpose Lubricant on the lip of the seal. 2. Use a press and Tool (B) to install bearings (4) on shaft (3). 3. Put 1P-0808 General Purpose Lubricant on the bearings and in the bearing bore of housing (2).4. Use a press and install shaft (3) and the bearings in housing (2). 5. Use Tool (C) and install ring (5) in the housing. 6. Inspect seal (6) for wear or damage and make a replacement if necessary.7. Put clean engine oil on seal (6) and install the seal on the shaft as shown. 8. Put plate (8) in position in body assembly (7) as shown. 9. Make an alignment of the dowel (10) in body assembly (7) with cam (9). Install cam (9) in body assembly (7). 10. Install housing (2) on body assembly (7) and install the bolts that hold the two together. Parts (11), (12), (13) and (14) come as a seal assembly only.11. Put clean engine oil on the rubber part only of ceramic seal (11).12. Put clean engine oil in the seal bore of the body assembly and install ceramic seal (11), polished surface toward the impeller. If the face of the seal is damaged (marked, scratched) a replacement must be made. 13. Install seal (12) in the body assembly with the polished carbon seal face of the seal toward the ceramic seal. 14. Install spring (13) and cover (14) in the body assembly. 15. Use Tool (D) and install ring (15) on the shaft that holds the seal assembly in place. 16. Inspect seal (16) for wear or damage and make a replacement if necessary.17. Put clean engine oil on seal (16) and install on the shaft. 18. Put a small amount of 1P-0808 General Purpose Lubricant in the impeller bore.19. Make sure all impeller blades are bent in the same direction and in the correct direction of rotation.20. Use Tool (E) and install impeller assembly (17) in the body assembly. 21. Install seal (18) in the impeller assembly. 22. Install gasket (19) and plate (21) on cover assembly (20).23. Make an alignment of the dowel in cover assembly (20) and the dowel hole in the cam and install cover assembly (20) with the screws that hold it.End By:a. install raw water pump


Parts hose Mercury:

17668
 
17668 HOSE (6-1/2")
1004137, 1004201FB, 1004201JK, 1004201VB, 1B04201FB, 1F04201WB
17669
 
17669 HOSE (5-1/4")
1004137, 1004201FB, 1004201JK, 1004201VB
812940
HOSE
812940 HOSE
1004137, 1004201JK, 1040203YL, 1040213YL
16246
 
16246 HOSE, FUEL
1004137, 1004201JK
16167
 
16167 HOSE, WATER PUMP
1004137, 1004201FB, 1004201JK, 1004201VB, 1B04201FB, 1F04201WB
815041
HOSE
815041 HOSE
1004201FB, 1004201JK, 1004201VB
815047
 
815047 HOSE
1004201JK
815049
 
815049 HOSE
1004201FB, 1004201JK, 1004201VB, 1B04201FB, 1F04201WB
Back to top