16789A42 Mercury HOSE ASSEMBLY, Fuel


16789A42 HOSE ASSEMBLY, Fuel Mercury 1040203YL, 1040213YL HOSE
16789A42 HOSE ASSEMBLY, Fuel Mercury
Rating:
103

Buy HOSE ASSEMBLY, Fuel 16789A42 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 6
 

Compatible models:

Mercury entire parts catalog list:

1040203YL 2001,2002,2003,2004
1040213YL 2001,2004

Information:


Table 1
Diagnostic Trouble Codes
J1939 Code CDL Code Code Description Comments
168-2 168-2 Battery Potential / Power Input #1 : Erratic, Intermittent, or Incorrect This code indicates that the battery circuit to the ECM is intermittent.
168-3 168-3 Battery Potential / Power Input #1 : Voltage Above Normal The ECM detects voltage that is above the acceptable value.
168-4 168-4 Battery Potential / Power Input 1 : Voltage Below Normal The ECM detects voltage that is below the acceptable value.
Follow the troubleshooting procedure to identify the root cause of the fault.
Illustration 1 g06409461
Typical example of the schematic for the electrical power supply circuit
Illustration 2 g06409491
View of the pin locations on the P1 connector for the ignition keyswitch and battery supply circuit
(5) Ignition keyswitch
(6) Ignition keyswitch
(12) Battery -
(13) Battery +
(26) Main power relay
(27) Main power relay
(36) Battery -
(37) Battery +
(60) Battery -
(61) Battery +
(62) Battery -
(70) Battery +
Table 2
Troubleshooting Test Steps Value Results
1. Determine the Diagnostic Code
A. Establish communication between the electronic service tool and the ECM . Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. Start the engine. Run the engine until the engine is at normal operating temperature.
C. Observe the "Active Diagnostic" screen on the electronic service tool. Wait at least 30 seconds so that any codes may become active.
Diagnostic code
Result: One of the diagnostic codes listed in Table 1 is active.
Proceed to Test Step 2.
Result: The electronic service tool will not communicate with the ECM.
Repair: Refer to Troubleshooting, "Electronic Service Tool Does Not Communicate".
2. Check the Charging Circuit
A. Check the charging circuit. Refer to Systems Operation, Testing and Adjusting, "Charging System - Test".
Charging circuit
Result: The charging system is OK.
Proceed to Test Step 3.
Result: The charging system is not OK.
Repair: There is a fault in the charging system. Make the necessary repairs.
Use the electronic service tool to clear all logged diagnostic codes and verify that the repair eliminates the fault.
3. Load Test the Batteries
A. Use a suitable battery load tester to test the batteries. Refer to Systems Operation, Testing and Adjusting, "Battery - Test" for the correct procedure.
Load test
Result: The batteries pass the load test.
Proceed to Test Step 4.
Result: The batteries do not pass the load test.
Repair: Recharge or replace the faulty batteries.
Use the electronic service tool to clear all logged diagnostic codes and verify that the repair eliminates the fault.
4. Inspect Electrical Connectors and Wiring
A. Ensure that the battery disconnect switch is in the CLOSED position.
B. Thoroughly inspect all connectors associated with the electrical power supplies.
C. Check all fuses.
D. Perform a 45 N (10 lb) pull test on each of the wires in the connectors associated with the electrical power supplies.
E. Check all the wiring associated with the electrical power supplies for abrasions and pinch points.
F. Verify that the "System Operating Voltage Configuration" is correctly configured in the Engine ECM configuration parameters.
Damaged wire or connector. Blown fuse.
Result: A damaged wire or damaged connector was found. A blown fuse was found.
Repair: Repair the damaged wire or the damaged connector. Replace all blown fuses.
Use the electronic service tool to clear all logged diagnostic codes. Verify that the repair eliminates the fault.
Result: The "System Operating Voltage Configuration" is configured incorrectly.
Repair: Program the parameter with the correct system voltage.
Result: A damaged wire or damaged connector was not found. The fuses are OK.
Contact the Dealer Solutions Network (DSN).


Parts hose Mercury:

812940
HOSE
812940 HOSE
1004137, 1004201JK, 1040203YL, 1040213YL
824965
 
824965 HOSE
1004201JK, 1040203YL, 1040213YL
830765
 
830765 HOSE (MOLDED)
1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1040213YL, 1041312UB
877680Q 8
 
877680Q 8 HOSE ASSEMBLY, Fuel (8 Feet)
1006201DB, 1006201VB, 1010207VB, 1011201DB, 1020201DB, 1020201VB, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040213YL, 1043203DD, 1043203VD, 1043213DD, 1043302DD, 1043411DD, 1043412DB, 1043412DD, 1050302DB, 1050302FB, 1050302FD, 1050312FB, 1050411D
877680Q12
 
877680Q12 HOSE ASSEMBLY, Fuel (12 Feet)
1006201DB, 1006201VB, 1010207VB, 1011201DB, 1020201DB, 1020201VB, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040213YL, 1043203DD, 1043203VD, 1043213DD, 1043302DD, 1043411DD, 1043412DB, 1043412DD, 1050302DB, 1050302FB, 1050302FD, 1050312FB, 1050411D
892037
 
892037 HOSE, Molded
1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040213YL
892038
 
892038 HOSE, Molded
1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040213YL
898101272
 
898101272 HOSE, Rubber with Arrow (730mm)
1008201YM, 1015203YL, 1030201YL, 1031207ZF, 1040203YL, 1040213YL, 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ
Back to top