889246T26 Mercury HOUSING, Volute


889246T26 HOUSING, Volute Mercury 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ HOUSING
889246T26 HOUSING, Volute Mercury
Rating:
8

Buy HOUSING, Volute 889246T26 Mercury genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$1,694.50
 

28-09-2017

Boating Ac: Boating Accessories
New Mercury Mercruiser Quicksilver Oem Part # 889246T26 Housing-Volute
Number on catalog scheme: 1
 

Compatible models:

Mercury entire parts catalog list:

1A25203FK 2006
1A25203FL 2006
1A25311FK 2006
1A25312FK 2006
1A30413KZ 2010

Information:

1. Remove upper drive shaft guard (1). Drain the hydraulic oil from the flywheel housing. 2. Disconnect hose (2) and two clips (3). Disconnect elbow (4) from the housing. 3. Disconnect the breather line (not shown) at the top of the retarder. Remove air compressor supply line and elbow (5) and discharge line (6). 4. Fasten tool (A) to top of retarder housing. Fasten hoist to tool (A). 5. Remove bolts (7) from the housing and lower retarder out the bottom. Weight of the retarder is 300 lb. (135 kg).Install Retarder
1. Check O-ring seal around housing and if damaged, use new seal for replacement. 2. Fasten tool (A) to retarder and fasten hoist to tool (A). Lift retarder (1) up from the bottom and put it in position on flywheel housing. Install the bolts that hold the retarder in position.3. Connect the line to the breather at the top of the retarder. Install the air compressor discharge line and supply line and elbow. 4. Install elbow (4) to the bottom of the retarder. Install two clips (3) and hose (2) to the retarder.5. Install the upper drive shaft guard.end by:a) install retarder control valveb) install drive shaftc) install exhaust crossover manifold and mufflerDisassemble Retarder
start by:a) remove retarder 1. Remove two bolts (3), lock (2), plate (1) and gear (4). 2. Remove bolts (5) from stator (6). 3. Install two 3/8"-16 NC forcing screws (7). Tighten the screws evenly to loosen the stator from the retarder housing.4. Remove the forcing screws and install two 3/8"-16 NC forged eyebolts. Fasten a hoist to the stator and remove the stator. Weight of stator is 60 lb. (27 kg). Remove the O-ring seal from the stator. 5. Remove rotor (8). 6. Remove snap ring (9) from the rotor. 7. Remove bearing (10) and retainer (11). Use pry bars as shown. 8. Remove ring (12) from the carrier. Remove the carrier only if necessary. 9. Install tooling (A) in the ring groove of the carrier. Remove carrier (13). 10. Turn rotor as shown. Remove snap ring (15) and two rings (14) from the carrier.11. Remove carrier only if necessary. Use same procedure as in Step 9. 12. Install two 3/8"-16 NC forged eyebolts (16). Fasten a hoist to the housing. Remove housing (17) from the yoke assembly. Weight of the housing is 130 lb. (59 kg). 13. Turn the housing as shown. Remove bolts (18). Remove cage (19) from the housing. Remove the O-ring seal from the cage. 14. Remove seal (20) from the cage. 15. Remove the bearing from the cage with tool (B).
Remove the race from the bore toward the inside of the housing as shown.
16. Remove race (21) from the housing. Remove O-ring seal (22). 17. Remove bolts (25), lock (23), retainer (26) and O-ring (not shown). Remove shaft (24) from yoke (27). 18. Remove race (28) from the yoke with tool (C).Assemble Retarder
1. Check seals and O-rings for damage. If damaged, use new parts for replacement. Heat race (1) in oil to a maximum temperature of 275°F (135°C) and install on yoke (2). 2. Put shaft (7) in position in the yoke. Install O-ring seal (5), retainer (4), lock (6) and bolts (3). Bend lock correctly against bolt heads.
Make sure race is installed against the counterbore of the housing.
3. Lower the temperature of race (8) and install the retarder housing. Install O-ring seal (9) in the retarder housing. 4. Install the bearing in cage (10) with tool (A). 5. Install the lip type seal in the cage with tool (A). Install the lip type seal until it makes contact with the counterbore and the lip is toward the bearing. 6. Install O-ring seal (11) in the cage. Install cage (10) on retarder housing (12). Install the four bolts that hold the cage in position on the housing. 7. Install 3/8"-16 NC forged eyebolts (13) in retarder housing (12). Fasten a hoist to the housing and install on the yoke assembly.
Carriers must be assembled correctly on rotor.
8. Heat the carrier with two ring grooves in oil to a maximum temperature of 275°F (135°C). Install carrier (14) on rotor (15). 9. Install the rings on the carrier with tool (B). 10. Install snap ring (16) that holds the carrier in position.11. Turn the rotor as shown. Heat the carrier with one ring groove in oil to a maximum temperature of 275°F (135°C) and install on the rotor. Install the ring on the carrier with tool (B). 12. Install retainer (17) on the rotor. 13. Install bearing (18) on the rotor. 14. Install snap ring (19) that holds the bearing in position on the rotor. Hoist is used for easy installation only. 15. Install two 3/8"-16 NC forged eyebolts (20) in the rotor. Fasten a hoist to the eyebolts and install rotor (15) in position on the shaft. 16. Install two 3/8"-16 NC guide bolts (21) in the retainer and two guide bolts in the retarder housing. Install O-ring seal (24). Install two 3/8"-16 NC forged eyebolts (22) in the stator and install stator (23) in position on the retarder housing with a hoist.17. Install the six bolts that hold the retainer to the stator and tighten the bolts to a torque of 36 5 lb.ft. (46 7 N m). Install the nineteen bolts that hold the stator to the retarder housing. Tighten the bolts to a torque of 40 5 lb.ft. (55 7 N m). 18.


Parts housing Mercury:

826053 1
 
826053 1 HOUSING, Water Pump
1025207FL, 1025207FM, 1025217FL, 1025217FM, 1030201FL, 1030201YL, 1030211FL, 1030271HL, 1030302FL, 1030312FL, 1030A01FL, 1030A11FL, 1031207ZF, 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ
801412T01
 
801412T01 HOUSING ASSEMBLY, Intake
1025207FL, 1025207FM, 1025217FL, 1025217FM, 1030201FL, 1030211FL, 1030271HL, 1030302FL, 1030312FL, 1030A01FL, 1030A11FL, 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ
889246025
HOUSING, Water Pump
889246025 HOUSING, Water Pump
1025207FL, 1025207FM, 1025217FL, 1025217FM, 1030201FL, 1030211FL, 1030271HL, 1030302FL, 1030312FL, 1030A01FL, 1030A11FL, 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ
803724T02
HOUSING, Driveshaft
803724T02 HOUSING, Driveshaft
1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ
803725T02
 
803725T02 HOUSING, Driveshaft
1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ
803750T05
 
803750T05 HOUSING, Water Pump
1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ
898103T19
HOUSING, Starter
898103T19 HOUSING, Starter
1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ
8M0051387
HOUSING
8M0051387 HOUSING
1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ
Back to top