817426 Mercury INSERT, Choke Bezel


817426 INSERT, Choke Bezel Mercury 1006201RB, 1006211RD, 1010207VB, 1011201DB, 1016207PD, 1016207RB, 1016207SB, 10202014D, 1020201BC, 1020201DB, 1020201VB INSERT
817426 INSERT, Choke Bezel Mercury
Rating:
23

Buy INSERT, Choke Bezel 817426 Mercury genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$92.76

14-12-2024
0.8818[0.40] pounds
CN: zhengzhoushizhengdon
RFLCZKLA Replacement Carburetor 817426 Fits and 420 BS420 Engine Parts
RFLCZKLA Durability Designed Compatible with performance in engines, ensuring reliable operation. || Compatibility Engineered to fit & 420 models simplifying installation and use. || Efficiency Optimizes fuel flow Compatible with improved combustion and enhanced engine performance. || Maintenance Simplifies upkeep with easy access to components, reducing service time and effort. || Reliability Offers consistent performance under various operating conditions Compatible with peace of mind.
$16.00
 

08-05-2024
0.31[0.14] pounds
US: Big Wide Seller
New Mercury Mercruiser Quicksilver OEM Part # 817426 INSERT
MERCURY
Number on catalog scheme: 30
 

Mercury entire parts catalog list:

1006201RB 1995
1006211RD 1995
1010207VB 1999,2000,2001,2002,2003,2004
1011201DB 2005,2006
1016207PD 1994
1016207RB 1995
1016207SB 1996
10202014D 1994,1995,1996,1997,1998
1020201BC 1988,1989,1990,1991,1992,1993,1994
1020201DB 2005,2006
1020201VB 1999,2000,2001,2002,2003,2004

Information:

1. Remove bolts (1) and lift shaft (2) and the rocker arms off the valve cover base and the push rods. 2. Remove push rods (3) from the valve lifters and valve cover base. 3. Remove bridge assemblies (4) from the dowels.Install Rocker Shaft Assemblies & Push Rods
1. Loosen the adjustment nuts and screws (1) on valve bridges (2).2. Put clean engine oil on the bridge dowels, the inside diameter of valve bridges (2) and on the top pad of the valve bridge. Install valve bridges (2) on the bridge dowels as shown.3. While bridges (2) are pushed straight down with a force of 25 20 N (5.6 4.5 lb) on the top contact surface, turn adjustment screw (1) until it makes contact with the valve stem. Turn screw (1) another 20 to 30 degrees. This will straighten the dowel in the guide and make compensation for clearance (slack) in the threads.4. Hold adjustment screw (1) in position and tighten the nut around screw (1) to a torque of 30 4 N m (22 3 lb ft). 5. Put push rods (3) in position in the valve lifters and valve cover base.
Make sure the crankshaft and camshafts are in time with each other and that adjustment screws (5) are turned all the way out before the rocker shaft bolts are tightened or damage to the valves or pistons can be the result. See the topic "Install Camshafts" for the procedure to time the engine.
6. Put the rocker arms and shaft (4) in position on the valve cover base. Make sure the rocker shafts and push rods are in alignment and install the bolts to hold shaft (4).7. Make an adjustment of the valves to have a clearance of 0.40 mm (.016 in) for intake and 0.76 mm (.030 in) for exhaust. See the topic "Valve Clearance Setting" in the Testing & Adjusting Manual for the complete procedure.End By:a. install valve coversDisassemble Rocker Shaft Assemblies
Start By:a. remove rocker shaft assemblies 1. Slide shaft assembly (1) out of rocker arms (2). If necessary, remove the dowel from shaft assembly (1). 2. Remove adjustment screw (4) and the nut from rocker arm (2).3. Use a hammer and punch to push socket (3) out of rocker arm (2). 4. Remove the ring that holds button (5) in socket (3) and remove the button from the socket. 5. Use Tool (A) to remove bearing (6) from rocker arm (2).6. Do Steps 2 through 5 for the other two rocker arms.Assemble Rocker Shaft Assemblies
1. Make an alignment of the oil hole (slot) in the bearing with the oil passage in rocker arm (1). Use Tool (A) to install the bearing in rocker arm (1) with the joint in the bearing toward the top of the rocker arm. The bore in the bearing must be 37.140 0.015 mm (1.4622 .0006 in) after assembly. 2. Make an alignment of the scribe mark on socket (2) with the mark on rocker arm (1) and install the socket in the rocker arm.3. Put button (3) in socket (2) and install ring (4) to hold the unit together. 4. Install adjustment screw (5) and nut (6) on rocker arm (1).5. Do Steps 1 through 4 for the other two rocker arms. 6. If the dowel was removed from shaft assembly (7), install the new dowel in the shaft until it is 7.70 0.50 mm (.303 .020 in) above the surface of the shaft.7. Put clean engine oil on the rocker arm bearings and shaft assembly (7). Install rocker arms (1) on shaft assembly (7).End By:a. install rocker shaft assemblies


Parts insert Mercury:

41750
 
41750 INSERT
1006201RB, 1006211RD, 1010207VB, 1011201DB, 1016207PD, 1016207RB, 1016207SB, 10202014D, 1020201BC, 1020201DB, 1020201VB
Back to top