811685 Mercury JET, POWER


811685 JET, POWER Mercury 11354120D, 1150453JD JET
811685 JET, POWER Mercury
Rating:
13

Buy JET, POWER 811685 Mercury genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$103.46
 

12-05-2021
0.2[0.00] Pounds
-: -
Vertex 811685 Complete Gasket Set
These sets include all gaskets and seals necessary to rebuild the engine and transmission.
Number on catalog scheme: 35
 

Compatible models:

Mercury entire parts catalog list:

11354120D 1990,1991
1150453JD 1990

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-5598 Anti-Seize Compound -
B 195-4609 Seal Pick 1
C Isopropyl Alcohol -
D 5P-4996 Plug 2 Start By:
Remove the Exhaust Elbow.
Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire. To help prevent possible injury, turn the start switch off when changing fuel filters or water separator elements. Clean up fuel spills immediately.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool.
Turn the fuel supply to the OFF position and turn the power disconnect switch to the OFF.
Illustration 1 g02797639
Disconnect clamp assemblies (1) and remove hose (2).
Remove bolts (4) and remove tube assembly (3) and the gasket. Discard the gasket. Note: Cap all hose assemblies, with Tooling (D), and fittings that are disconnected o prevent fluid loss. This action will also keep contaminants out of the systems.
Illustration 2 g02797644
Remove bolt (5) and disconnect harness assembly (6).
Illustration 3 g02797650
Disconnect hose assemblies (7) and hose assembly (8).
Remove allen bolt (9), the clamp assembly, and position cable assembly (10) out of the way.
Disconnect flame detection temperature sensor (11).
Illustration 4 g02153382
Remove nuts (16) and remove combustion head (15).
Remove gasket (14), tube assembly (13), and gasket (12). Discard the gaskets. Note: The gaskets are for one time use only. Replace with new gaskets upon installation.
If required, remove studs (17).
Illustration 5 g02797661
Remove fittings (18) and (19).
Remove spark plug (20) and remove fittings (21).
Illustration 6 g02481277
Use Tooling (B) in order to remove O-ring seals (22) and (23) from cable assembly (10). Discard the O-ring seals. Installation Procedure
Install combustion head (15) in reverse order.
Apply Tooling (A) onto the threads of studs (17). Install the studs. Tighten studs (17) to a torque of 17 2 N m (150 18 lb in).
Apply Tooling (A) onto the threads of the studs and nuts (16). Tighten nuts (16) in a crisscross pattern to a torque of 23 3 N m (17 2 lb ft). Tighten nuts (16) again in a crisscross pattern to a torque of 28 3 N m (21 2 lb ft). Tighten nuts (16) again in a crisscross pattern to a torque of 28 3 N m (21 2 lb ft).
Use caution when you are using isopropyl alcohol. Avoid prolonged skin contact with isopropyl alcohol.Vapors may be harmful if inhaled. Use only in a well ventilated area. Do not smoke while using isopropyl alcohol.Isopropyl alcohol is flammable. Do not use near an open flame or near welding operations. Keep isopropyl alcohol away from heated surfaces exceeding 482°C (900°F).
Note: This connection is an electrical connection and cannot be lubricated with a petroleum-based lubricant. Isopropyl alcohol is the only approved lubrication for this connection.
Lubricate new O-ring seals (22) and (23) with Tooling (C) prior to installation.
Tighten fitting (21) to a torque of 60 6 N m (44 4 lb ft).
Tighten fittings (19) and (18) to a torque of 30 2 N m (266 18 lb in).
Tighten spark plug (20) to a torque of 47 4 N m (35 3 lb ft).


Parts jet Mercury:

3026
 
3026 JET,MAIN FUEL(.036)
1005200, 1040100, 1040102, 1045205, 11354120D, 1135412SD, 1135412VD, 1135412WD, 1150453JD
3251
 
3251 JET,MAIN FUEL(.034)
1005200, 1040100, 1040102, 1045205, 1075101, 1075202, 1075204, 11354120D, 1135412SD, 1150453JD
3796
 
3796 JET, MAIN FUEL (.076)
10202014D, 1020201DB, 1020201VB, 1040208, 1090524, 1100312BD, 1100412VB, 1115412DB, 1115520, 1115523, 1115525, 1135100, 11354120D, 1140528, 1150453BD, 1150453GD, 1150453JD, 1150503, 1150538, 1150625, 1200628, 1225412PD, 1300623, 1400100, 1402202, 140
3794
 
3794 JET, MAIN FUEL (.074)
1035204, 1035207, 1040200, 1040208, 1050312BC, 1090520, 1090524, 1090528, 1115503, 1115520, 1115523, 1115525, 1115528, 1135100, 1135412SD, 1135412VD, 1135412WD, 1140520, 1140629, 1150453BD, 1150453GD, 1150453JD, 1175626, 1200628, 1225412PD, 1300623,
4216
 
4216 JET, MAIN FUEL (.064)
1006201RB, 1006211RD, 1016207RB, 1070312BC, 1070717, 1075217DD, 1075217FD, 1075217PD, 1075217VD, 10752L7DF, 10752L7FF, 1075317DB, 1075317FB, 10754120D, 1075412DB, 1075412DD, 1075412DN, 1075412FB, 1075412FY, 1090412DB, 1090412DC, 1090412DD, 1090412DN,
19266036
 
19266036 JET, IDLE AIR BLEED
11354120D, 1150453JD
810742
JET, (.044), PROGRESSION AIR
810742 JET, (.044), PROGRESSION AIR
11354120D, 1135412SD, 1135412VD, 1135412WD, 1150453JD, 1225412VD
810741
JET, (.030), PROGRESSION AIR
810741 JET, (.030), PROGRESSION AIR
11354120D, 1135412SD, 1135412VD, 1135412WD, 1150453JD, 1225412PD
Back to top