815633028 Mercury JET, (.028)


815633028 JET, (.028) Mercury 1135412SD, 1135412VD, 1135412WD JET
815633028 JET, (.028) Mercury
Rating:
68

Buy JET, (.028) 815633028 Mercury genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$16.99
 

22-04-2021
0.01543235834[0.00] Pound
-: -
New Mercury Mercruiser Quicksilver Oem Part # 815633028 Jet-.028
Number on catalog scheme: 6
 

Compatible models:

Mercury entire parts catalog list:

1135412SD 1996,1997,1998
1135412VD 1999
1135412WD 2000,2001,2002,2003,2004,2005

Information:

Probable Causes
Active engine shutdown
Electrical connectors or power supply
Circuit breaker
Engine speed/timing signal
Fuel supply
Fuel quality
Spark plugRecommended Actions
Active Engine Shutdown
Use the Caterpillar Electronic Technician (ET) to check for any active engine shutdowns and/or logged engine shutdowns. Determine the reason for the shutdown. After correcting the problem, set the engine control to the OFF/RESET mode for at least 15 seconds before you try to restart the engine.Electrical Connectors or Power Supply
Check the wiring harnesses and the connectors. Inspect the connectors in the terminal box. Inspect the power supply connections and the ground. Refer to Troubleshooting, "Electrical Connectors - Inspect".
Use Cat ET to check for the 168-02 diagnostic code for erratic system voltage. If this diagnostic code is logged, proceed to Troubleshooting, "Electrical Power Supply - Test".
Inspect the wiring from the power supply to the power distribution box. Inspect the wiring from the power distribution box to the electronic control modules. Check the power and ground connections at each electronic control module. Refer to Troubleshooting, "Electrical Power Supply - Test" for more information. Circuit Breakers
Check the 35 amp circuit breaker on the power distribution box. The circuit breaker may exceed the trip point due to overheating. Reset the circuit breaker if the circuit breaker is tripped.Engine Speed/Timing Signal
Loss of the signal from the engine speed/timing sensor will cause a shutdown. Use Cat ET to check for logged diagnostic codes. For more information, refer to Troubleshooting, "Speed/Timing - Test".Fuel Supply
Use Cat ET to check that the engine's fuel parameters are correct for the fuel that is being used. If necessary, perform fuel analysis in order to confirm the fuel quality.Verify that the fuel pressure is correct. When possible, interview the operator in order to determine if fuel quality is in question. Try to determine if the source of the fuel has been changed.Ensure that fuel is supplied at a sufficient pressure that is stable. Check that the size of the fuel line is sufficient. Inspect the fuel system for leaks.The following conditions can affect engine starting:
Low fuel pressure
High fuel pressure
Poor fuel qualityInspect the following fuel system components:
Fuel filter
Gas pressure regulator
Gas shutoff valve
Fuel metering valveCheck the fuel metering valve's status indicator that is located on the top of the valve. If the status indicator is flashing orange or flashing red there is an internal error for the valve. Before performing maintenance on the valve, observe the status indicator. Refer to Operation and Maintenance Manual, SEBU7630, "WOODWARD RAPTOR GAS REGULATION AND METERING VALVE/ACTUATOR SYSTEM" for detailed information about flash codes and for information that is related to troubleshooting the fuel metering valve.Verify that the system's components are operating correctly.Repair suspect components. Replace the fuel filter, if necessary.Fuel Quality
Compare the Low Heat Value (LHV) of the gas supply to the "Fuel Quality" parameter that is programmed by the customer into the master Electronic Control Module (ECM). The master ECM uses the setting for start-up and for air/fuel ratio control at low loads.If the LHV of the fuel does not match the "Fuel Quality" parameter that is programmed into the master ECM, program the correct setting for the "Fuel Quality" parameter.Spark Plug
An engine shutdown that is due to a faulty spark plug is likely to occur when the engine is operating under a load. Refer to Troubleshooting, "Ignition Secondary - Test".


Parts jet Mercury:

3026
 
3026 JET,MAIN FUEL(.036)
1005200, 1040100, 1040102, 1045205, 11354120D, 1135412SD, 1135412VD, 1135412WD, 1150453JD
3251
 
3251 JET,MAIN FUEL(.034)
1005200, 1040100, 1040102, 1045205, 1075101, 1075202, 1075204, 11354120D, 1135412SD, 1150453JD
810742
JET, (.044), PROGRESSION AIR
810742 JET, (.044), PROGRESSION AIR
11354120D, 1135412SD, 1135412VD, 1135412WD, 1150453JD, 1225412VD
801401150
 
801401150 JET PUMP (GRAY)
1135412MD, 1135412SD
815633042
 
815633042 JET, Idle Air Vent (.042-TOP)
1135412SD, 1135412VD, 1225412PD
815633038
JET, (.038) (TOP)
815633038 JET, (.038) (TOP)
1135412SD, 1135412VD, 1135412WD, 1225412PD
815633054
JET, (.054) (CENTER)
815633054 JET, (.054) (CENTER)
1135412WD, 1225412PD, 1225412VD
815633046
JET, (.046) (TOP)
815633046 JET, (.046) (TOP)
1135412WD, 1225412PD, 1225412VD
Back to top