76176 Mercury LEVER. FRONT COVER


76176 LEVER. FRONT COVER Mercury 1020208, 1035204, 1035207, 1040200, 1040208, 1402205 LEVER
76176 LEVER. FRONT COVER Mercury
Rating:
28

Buy LEVER. FRONT COVER 76176 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 13
 

Compatible models:

Mercury entire parts catalog list:

1020208 1978,1979,1980
1035204 1984,1985,1986
1035207 1987,1988,1989
1040200 1980,1982,1983
1040208 1978,1979
1402205 1975,1976,1977

Information:


Table 1
Diagnostic Trouble Codes
J1939 Code CDL Code Code Description Comments
168-2 168-2 Battery Potential / Power Input #1 : Erratic, Intermittent, or Incorrect This code indicates that the battery circuit to the ECM is intermittent.
168-3 168-3 Battery Potential / Power Input #1 : Voltage Above Normal The ECM detects voltage that is above the acceptable value.
168-4 168-4 Battery Potential / Power Input 1 : Voltage Below Normal The ECM detects voltage that is below the acceptable value.
Follow the troubleshooting procedure to identify the root cause of the fault.
Illustration 1 g03366300
Typical example of the schematic for the electrical power supply circuit
Illustration 2 g03366309
View of the pin locations on the P1 connector for the ignition keyswitch and battery supply circuit
(1) Battery ground
(2) Battery ground
(3) Battery ground
(7) Battery+
(8) Battery+
(9) Battery ground
(10) Battery ground
(15) Battery+
(16) Battery+
(40) Ignition keyswitch
Table 2
Troubleshooting Test Steps Value Results
1. Determine the Diagnostic Code
A. Establish communication between the electronic service tool and the ECM . Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. Start the engine. Run the engine until the engine is at normal operating temperature.
C. Observe the "Active Diagnostic" screen on the electronic service tool. Wait at least 30 seconds so that any codes may become active.
Diagnostic code
Result: One of the diagnostic codes listed in Table 1 is active.
Proceed to Test Step 2.
Result: The electronic service tool will not communicate with the ECM.
Repair: Refer to Troubleshooting, "Electronic Service Tool Does Not Communicate".
2. Check the Charging Circuit
A. Check the charging circuit. Refer to Systems Operation, Testing and Adjusting, "Charging System - Test".
Charging circuit
Result: The charging system is OK.
Proceed to Test Step 3.
Result: The charging system is not OK.
Repair: There is a fault in the charging system. Make the necessary repairs.
Use the electronic service tool to clear all logged diagnostic codes and verify that the repair eliminates the fault.
3. Load Test the Batteries
A. Use a suitable battery load tester to test the batteries. Refer to Systems Operation, Testing and Adjusting, "Battery - Test" for the correct procedure.
Load test
Result: The batteries pass the load test.
Proceed to Test Step 4.
Result: The batteries do not pass the load test.
Repair: Recharge or replace the faulty batteries.
Use the electronic service tool to clear all logged diagnostic codes and verify that the repair eliminates the fault.
4. Inspect Electrical Connectors and Wiring
A. Ensure that the battery disconnect switch is in the CLOSED position.
B. Thoroughly inspect all connectors associated with the electrical power supplies.
C. Check all fuses.
D. Perform a 45 N (10 lb) pull test on each of the wires in the connectors associated with the electrical power supplies.
E. Check all the wiring associated with the electrical power supplies for abrasions and pinch points.
F. Verify that the "System Operating Voltage Configuration" is correctly configured in the Engine ECM configuration parameters.
Damaged wire or connector. Blown fuse.
Result: A damaged wire or damaged connector was found. A blown fuse was found.
Repair: Repair the damaged wire or the damaged connector. Replace all blown fuses.
Use the electronic service tool to clear all logged diagnostic codes. Verify that the repair eliminates the fault.
Result: The "System Operating Voltage Configuration" is configured incorrectly.
Repair: Program the parameter with the correct system voltage.
Result: A damaged wire or damaged connector was not found. The fuses are OK.
Contact the Dealer Solutions Network (DSN).


Parts lever Mercury:

55180
 
55180 LEVER, CHOKE
1035204, 1035207, 1040200, 1040208, 1400100, 1402202, 1402205
47912A 2
 
47912A 2 LEVER ASSEMBLY, TILT STOP - STARBOARD SIDE
1035204, 1035207, 1040200, 1040208, 1400100, 1402202, 1402205
47913A 2
 
47913A 2 LEVER ASSEMBLY, TILT LOCK - PORT SIDE
1035204, 1035207, 1040200, 1040208, 1400100, 1402202, 1402205
94918
 
94918 LEVER, COWL LATCH HINGE
1035204, 1040200, 1050200, 1080500, 1090520, 1115520, 1115523
94962A 1
95049
 
95049 LEVER, THROTTLE CONTROL
1035204, 1035207, 1040200
95051
 
95051 LEVER, SPARK ADVANCE
1035204, 1035207, 1040200
94918T
LEVER, COWL LATCH HINGE
94918T LEVER, COWL LATCH HINGE
1035207, 1045217, 1075524, 1090524, 1115525
Back to top