858925 Mercury LEVER, Lock, Upper


858925 LEVER, Lock, Upper Mercury 1020201DB LEVER
858925 LEVER, Lock, Upper Mercury
Rating:
98

Buy LEVER, Lock, Upper 858925 Mercury genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$39.21
 

12-09-2023
0.0462[0.02] Pounds
-: -
New Mercury Mercruiser Quicksilver OEM Part # 858925 LEVER-LOCK-UPPER
Number on catalog scheme: 24
 

Compatible models:

1020201DB   Mercury

Mercury entire parts catalog list:

1020201DB 2005,2006

Information:

Introduction
The purpose of this special instruction is to provide detailed instructions to allow the creation of 4 separate troubleshooting harnesses that can be used to troubleshoot issues with the overmold harness installed on C175 engines.Each harness outlined in this instruction is different and is designed to fit a different area related to the overmold harness.Do not perform any procedure in this Special Instruction until you have read the information and you understand the information.Safety Section
Do not operate or work on this product unless you have read and understood the instruction and warnings in the relevant Operation and Maintenance Manuals and relevant service literature. Failure to follow the instructions or heed the warnings could result in injury or death. Proper care is your responsibility.
Failure to follow all safety guidelines prescribed in this document and by governing authorities and regulatory agencies may result in severe injury or death of personnel or machine damage.
Personal injury or death can result from improper maintenance procedures. To avoid injury or death, follow the procedures exactly as stated below.
Before servicing/performing maintenance on the machine, electrical power must be physically disconnected; battery plugs must be disconnected from the batteries, or the trailing cable must be unplugged, and warning tags and padlocks shall be applied by a certified electrician. Certified electricians shall perform or direct any electrical work, including any energized testing, repair work in controllers, motors, or other approved compartments, and shall insure that all compartments are properly closed and inspected prior to re-energization. All applicable lock out and tag out procedures must be followed.
Required Parts
Table 1
Part Number Part Name Qty
7K-1181 Cable Strap 11
9X-0347 Connector Plug As 1
9X-3401 Connector Pin 330
9X-3402 Connector Socket 660
9X-4391 Connector Plug As 1
103-0213 Connector Receptacle As 2
125-7875 Heat Shrink Tube 165 cm (65 inch)
133-8753 Connector Receptacle As 1
160-7689 Connector Plug As 2
175-7061 Connector Receptacle As 2
264-5732 Connector Plug As 2
324-5680 Connector Receptacle As 1
N/A Butt Connector - Splice 330
N/A 16 AWG Wire 515 m (1689 ft) Examples of Wiring Harnesses
Illustration 1 g06455825
Illustration 2 g06461357Illustrations 1 and 2 depict 1 example of the 4 harnesses that would be needed.
Illustration 3 g06461469
(1) 264-5732 Connector Plug As (ECM Connector)
(2) Splice Location A
(3) 324-5680 Connector Receptacle As (Overmold Connector)
(4) 264-5732 Connector Plug As (Test Connector)
(5) Splice Location C
(6) Splice Location BIllustration 3 is an example of a template to help create each harness.Wire lengths vary, the beginning single wire lengths are staggered to minimize the bulge of wires in one area of the harness due to the splices. This also drives landing wire lengths to vary accordingly Wire connections are to be position to position. Example: socket 1 to socket 1 to pin 1 for each of the 3 connectors.The 3 cables straps tied together can help with wire routing to the 3 connectors.ECM to Overmold 120 Pin Test Harness
General information for the 120-Pin Y- Harness between ECM, Overfoam Harness, and Test Harness.
ECM-1 through 120 = Connector to ECM positions 1 through 120
Over-1 through 120 = Connector to Overfoam Harness positions 1 through 120
Test-1 through 120 = Connector for Test Instrument positions 1 through 120Because there are 120 splices needed for 120-pin Troubleshooting Harness, the splices have been broken out into 3 locations - reference slide 4 for general layout.
Location A Splices are on positions 31 through 75 - connector to ECM
Location B Splices are on positions 76 through 120 - connector to Test Instruments
Location C Splices are on positions 1 through 30 - connector to Overfoam Harn


Parts lever Mercury:

96965
 
96965 LEVER, TILT STOP - PORT SIDE
1018200, 1018204, 10202014D, 1020201BC, 1020201DB, 1020201VB, 1025200, 1F10203VD, 1F10352VD, 1F13203FB, 1F15201UD
90901
 
90901 LEVER, TILT STOP - STARBOARD SIDE
1006201DB, 1006201PD, 1006201RB, 1006201VB, 1006206, 1006211RD, 1008211RD, 1010207VB, 1011201DB, 1016207PD, 1016207RB, 1016207SB, 1018200, 1018204, 10202014D, 1020201BC, 1020201DB, 1020201VB, 1025200, 1F08203VF, 1F08261RF, 1F10203VD, 1F10352VD, 1F132
12758
 
12758 LEVER, CONTROL
1018204, 10202014D, 1020201BC, 1020201DB, 1020201VB, 1F10203VD, 1F10352VD, 1F13203FB, 1F15201UD
17220
 
17220 LEVER, Cowl Latch
1016207PD, 1016207RB, 1016207SB, 10202014D, 1020201BC, 1020201DB, 1020201VB
93876 2
 
93876 2 LEVER, LOCK (LOWER)
1016207PD, 1016207RB, 1016207SB, 10202014D, 1020201BC, 1020201DB, 1020201VB
823610 3
 
823610 3 LEVER, Interlock Control
10202014D, 1020201DB, 1020201VB
823862
LEVER, Backplate
823862 LEVER, Backplate
10202014D, 1020201DB, 1020201VB
823863 2
 
823863 2 LEVER, Horizontal Shift Shaft (PORT)
10202014D, 1020201DB, 1020201VB
Back to top