19385 25 Mercury LINK

Illustration 1 g00283070 (1) The dowels extend past the end of the cylinder block. Distance ... 8.0 0.5 mm (0.32 0.02 inch) (2) The dowels extend past the end of the cylinder block. Distance ... 8.0 0.5 mm (0.32 0.02 inch) (2) The dowels extend past the end of the cylinder block. Distance ... 10.0 0.5 mm (0.39 0.02 inch) (4) Cylinder liner
Illustration 2 g00283158
Section A-A
Bore diameters in the cylinder block for the cylinder block liners: Position (A) ... 151.50 0.03 mm (5.965 0.001 inch)Position (B) ... 148.00 0.03 mm (5.827 0.001 inch)Position (C) ... 141.90 0.15 mm (5.587 0.006 inch)
Illustration 3 g00283159 (5) Diameter of the camshaft bores ... 81.000 0.015 mm (3.1890 0.0006 inch) (6) Tighten the bolt that holds the piston cooling jet. Torque for the bolt ... 25 7 N m (18 5 lb ft) (7) Distance from the centerline of the crankshaft bore to the top surface of the cylinder block ... 387.00 mm (15.236 inch)The flatness of the top contact surface of the cylinder block must be within 0.05 mm (0.002 inch) for any 150 mm (5.9 inch) section of the surface. (8) Width of the main bearing cap ... 175.000 0.020 mm (6.8898 0.0008 inch)Width in cylinder block for the main bearing cap ... 175.000 0.018 mm (6.8898 0.0007 inch) (9) Distance from the centerline of the crankshaft to the bottom surface of the cylinder block ... 120.0 mm (4.72 inch) (10) Install the bolts for the main bearing cap. Use the procedure that follows. Install the bolts for the main bearing cap. The part number on the main bearing cap must face to the right and to the front face of the block. The tab slots that are in the block and the main bearing caps must be adjacent. The main bearing caps are marked with identification numbers 1 through 7. Install the main bearing caps into the correct positions. Lubricate the main bearing cap bolts. Use "SAE 30W" oil or molybdenum grease to lubricate the threads and the washer face. Tighten both main bearing cap bolts to the following torque. ... 95 5 N m (70 4 lb ft)Additionally tighten the bolts. ... 90 5 degrees (11) Bore in the cylinder block for the seven main bearings ... 116.000 0.013 mm (4.5669 0.0005 inch)Bore in the bearings for the crankshaft journals ... 108.102 0.031 mm (4.2560 0.0012 inch)Note: All of the measurements for the main bearing bore must be made before the main bearing cap is disassembled.
Illustration 4 g00283161
View B-B
The camshaft bearings are installed into the cylinder block at the values that follow. Position (A) ... 35.20 mm (1.386 inch)Position (B) ... 191.20 mm (7.528 inch)Position (C) ... 347.20 mm (13.669 inch)Position (D) ... 503.20 mm (19.811 inch)Position (E) ... 659.20 mm (29.953 inch)Position (F) ... 815.20 mm (32.094 inch)Position (G) ... 954.10 mm (37.563 inch)
Camshaft bearings must be installed into their correct position. Failure to do so will result in engine damage.
Illustration 5 g00283162
View C-C
Note: Illustration 5 represents camshaft bearing 7. (12) Bearing joint (A) Bearing oil hole at a 45 degree angle
Illustration 6 g00283163
View D-D
Note: Illustration 6 represents camshaft bearings 2 through 6. (13) Bearing joint (B) Bearing oil hole at a 45 degree angle
Illustration 7 g00283164
View E-E
Note: Illustration 7 represents camshaft bearing 1. (14) Oil hole Note: The width of the number 1 through number 6 camshaft bearing is 33.4 0.5 mm (1.32 0.02 inch). The width of the number 7 camshaft bearing is 28.0 0.5 mm (1.10 0.02 inch). The number 1 camshaft bearing has a 5.0 0.5 mm (0.20 0.02 inch) wide single groove on the inside diameter of the camshaft bearing. The width of the single groove on the outside diameter of camshaft bearings 2 through 6 is 8.0 0.5 mm (0.32 0.02 inch). A single groove is on the outside diameter of the number 7 camshaft bearing.