92876A 1 Mercury STEERING LINK ASSEMBLY


92876A 1 STEERING LINK ASSEMBLY Mercury 1035207, 1045217, 1070312BC, 1070717, 1075217PD, 10754120D, 1075524, 1090524, 1100312BD, 1100412PD, 1115525, 11354120D, 1135412GD, 1135412MD, 1135412SD, 1135412VD, 1135473UD, 1135726, 1150413SD, 1150413VD, 1150453BD, 1150453GD, 1150453JD, 1150625, 11 STEERING
92876A 1 STEERING LINK ASSEMBLY Mercury
Rating:
28

Buy STEERING LINK ASSEMBLY 92876A 1 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 15
 

Mercury entire parts catalog list:

1035207 1987,1988,1989
1045217 1987,1988,1989
1070312BC 1988,1989,1990
1070717 1987
1075217PD 1994,1995,1996,1997,1998
10754120D 1990,1991,1992,1993
1075524 1984,1985,1986
1090524 1984,1985,1986,1987,1988
1100312BD 1988,1989,1990,1991,1992,1993
1100412PD 1994,1995,1996,1997,1998
1115525 1985
11354120D 1990,1991
1135412GD 1989
1135412MD 1992,1993,1994,1995
1135412SD 1996,1997,1998
1135412VD 1999
1135473UD 1998
1135726 1986,1987,1988
1150413SD 1996,1997,1998
1150413VD 1999
1150453BD 1988
1150453GD 1989
1150453JD 1990
1150625 1985
1150628 1978,1979,1980,1982,1983,1984,1985
1175412GD 1989
1175413LD 1991
1175413MD 1992,1993,1994,1995
1175626 1976,1977,1978,1979,1980,1985,1986,1988
1200412GD 1989,1990
1200413GD 1989,1990
1200473TD 1997
1200473UD 1998
1220727 1987,1988
1225412PD 1994,1995,1996,1997,1998
1225413RD 1995,1996,1997,1998
1225620 1980
1250422GD 1989,1990,1991,1992,1993,1994
1300623 1983,1984,1985,1986,1987

Information:


Illustration 1 g01728067
Electronic unit injector
Test Step 1. Check for Diagnostic Codes that are Related to this Procedure
Connect the electronic service tool to the diagnostic connector.
Turn the keyswitch to the ON position.
Check for logged diagnostic codes that are related to this procedure.
Make a note of the logged diagnostic codes. Expected Result:Expected Result 1One or more of the following diagnostic codes are logged:
1-2 Cylinder #1 Injector erratic, intermittent, or incorrect
2-2 Cylinder #2 Injector erratic, intermittent, or incorrect
3-2 Cylinder #3 Injector erratic, intermittent, or incorrect
4-2 Cylinder #4 Injector erratic, intermittent, or incorrect
5-2 Cylinder #5 Injector erratic, intermittent, or incorrect
6-2 Cylinder #6 Injector erratic, intermittent, or incorrect Expected Result 2Injectors 1, 2 and 3 share a common injector driver circuit in the ECM. Injectors 4, 5 and 6 share a common driver circuit in the ECM. If three injectors that share a common supply indicate a diagnostic code then this is probably caused by a faulty ECM.Results:
OK - Result 1 One or more diagnostic codes are logged. Proceed to Test Step 2.
OK - Result 2 Three injectors that share a common supply indicate a diagnostic code. Proceed to Test Step 3.
Not OK - No related diagnostic codes are logged.STOPTest Step 2. Check the Faulty Cylinder Numbers
Use the electronic service tool in order to make a note of the logged diagnostic codes.
Use the noted diagnostic codes in order to check the cylinders for faulty injectors. Expected Result:The diagnostic codes indicate the cylinder numbers that have faulty injectors.Results:
OK - No related diagnostic codes are logged.STOP
Not OK - The diagnostic codes indicate the cylinder numbers that have faulty injectors.Repair: Replace the faulty injectors.Use the electronic service tool in order to program the replacement trim files for the injectors. Refer to Troubleshooting, "Injector Trim File" for further information.Use the electronic service tool in order to clear the logged codes.Turn the keyswitch to the ON position.Start the engine.Use the electronic service tool in order to perform the "Fuel System Verification Test". If the cylinders indicate "PASS", then the fault has been cleared.Verify that the repair eliminates the fault.STOPTest Step 3. Check the ECM
Make sure that the latest flash file for the application is installed in the ECM. Refer to Troubleshooting, "Flash Programming".
Contact the technical communicator at the Caterpillar dealer. Note: This consultation can greatly reduce the repair time.
If the technical communicator recommends the use of a test ECM, install a test ECM. Refer to Troubleshooting, "Replacing the ECM".
Use the electronic service tool in order to perform the "Fuel System Verification Test". Verify that the test eliminates the fault. Note: The "Fuel System Verification Test" will indicate if the cylinder has a "Pass" or "Fail". If the cylinders indicate "Pass" then the fault has been cleared.
If the test ECM eliminates the fault, reconnect the suspect ECM.
Use the electronic service tool in order to perform the "Fuel System Verification Test". Expected Result:The test ECM clears the fault. The "Fuel System Verification Test" with the suspect ECM indicates a "FAIL" condition.Results:
OK - The test ECM eliminates the fault and the suspect ECM indicates a "FAIL" condition. Replace the faulty ECM. Verify that the repair eliminates the fault.STOP
Not OK - The test ECM did not eliminate the fault.Repair: Reinstall the original ECM.Repeat the test procedure from Step1.


Parts steering Mercury:

75792A 1
 
75792A 1 STEERING LINK
1150625, 1150628, 1175626
19459A 3
 
19459A 3 STEERING ARM ASSEMBLY
1035207, 10402139D, 1050312BC
12020T
 
12020T STEERING ARM (MERCURY)
1070312BC, 1070717
92876A 8
STEERING ATTACHING KIT (SINGLE)
92876A 8 STEERING ATTACHING KIT (SINGLE)
1115F13CC, 1115F13FF, 1115F13YD, 1135412MD, 1135412VD, 1135412WD, 1150413VD, 1150413WD, 1175413MD, 1200D73AD, 1200D73CD, 1200D73ET, 1200D73HT, 1200E73EY, 1200E73HY, 1225412PD, 1225E73AD, 1256413WD, 192847GHD, 1B75412CF, 1B75413DF, 1F75411WD
Back to top