47276 Mercury LOCK RING, PISTON PIN


47276 LOCK RING, PISTON PIN Mercury 1016207PD, 1016207RB, 1016207SB, 1018200, 1018204, 1020100, 1020201BC, 1020202, 1020208, 1025200, 10402139D, 1045217, 1050200, 1200203, 1500100, 1500101, 1500205, 1500206 LOCK
47276 LOCK RING, PISTON PIN Mercury
Rating:
18

Buy LOCK RING, PISTON PIN 47276 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 13
 

Mercury entire parts catalog list:

1016207PD 1994
1016207RB 1995
1016207SB 1996
1018200 1980,1982,1983
1018204 1984,1985,1986,1987
1020100 1970
1020201BC 1988,1989,1990,1991,1992,1993,1994
1020202 1972
1020208 1978,1979,1980
1025200 1980,1982,1983
10402139D 1989,1990,1991,1992,1993,1994,1995,1996,1997
1045217 1987,1988,1989
1050200 1980,1982,1983,1984,1985,1986
1200203 1973,1974,1975,1976,1977
1500100 1970
1500101 1971,1972,1973,1974
1500205 1975
1500206 1976,1977,1978,1979

Information:

1. Loosen the bolts (2) that hold main bearing caps (1) to cylinder block. 2. Install one of the bolts for flywheel in each end of the crankshaft.3. Fasten a hoist and remove the main bearing caps. Remove bearings from bearing caps.4. Remove crankshaft from engine. Weight is 350 lb. (159 kg).5. Remove crankshaft main bearings from cylinder block. If new main bearings are not to be installed, keep old bearings with identification as to their location in cylinder block. 6. Use tooling (A) to remove crankshaft outer gear. Use a hammer and a chisel to remove spacer. 7. Use tooling (B) to remove dowel.8. Use tooling (A) to remove crankshaft inner gear.Install Crankshaft
1. Heat the crankshaft gears to a maximum temperature of 400°F (204°C). 2. Install crankshaft inner gear (2) on crankshaft.3. Install spacer on crankshaft.4. Install the pin in end of crankshaft. The pin must be extended no more than .19 in. (4.82 mm) from surface of crankshaft.5. Install the crankshaft outer gear (1) on crankshaft. the pin in crankshaft must be in alignment with notch in crankshaft gear (1).6. Clean the cylinder block and main bearing caps thoroughly. 7. Install upper half of main bearings (3) in the block. Put clean engine oil on the bearings and journals of crankshaft.8. Install one bolt for flywheel on each end of crankshaft.9. Fasten a hoist and put crankshaft in position in block. Make sure the "V" mark on the crankshaft gear is in alignment with the "V" mark on the idler gear. The "K" marks on the camshaft gear can be seen at the outer edges of the idler gear when the timing gears are in the correct position.10. Install main bearings in bearing caps. Be sure the tabs (4) on back of bearings fit in the grooves of caps and cylinder block.11. Use wire (B) to check bearing clearance.12. Put wire (B) on the bearing. Be sure main bearing caps (5) are installed so the numbers on the side of the cylinder block are the same as the numbers on the bearing caps, and the arrows on the caps are toward the front of the cylinder block.13. Install the main bearing caps. Install the bolts (6) and tighten the bolts, at end with tab first, to a torque of 190 10 lb.ft. (260 14 N m). Put a mark on the bolts and caps. Turn the bolts at opposite end of tab first an extra 120° 5° from the mark.14. Remove the main bearing caps. Remove wire (B) from the caps. Check the thickness of wire (B) to find the bearing clearance. The bearing clearance must be .0036 to .0073 in. (0.091 to 0.185 mm) with new bearings. Maximum clearance with used bearings is .010 in. (0.35 mm).15. Install the thrust bearings for No. 4 main bearing. Install the thrust bearings with the side marked "BLOCK SIDE" toward the cylinder block.16. Put clean engine oil on the threads of the bolts. Install the main bearing caps. Install the bolts and the bolts, at the end with the tab first, to a torque of 190 10 lb.ft. (260 14 N m). Put a mark on the bolts and caps. Turn the bolts, opposite end of tab first, an extra 120° 5° from the mark. 17. Check the end play of the crankshaft with tool group (A). Be sure the dial indicator is against a machined surface. The end play is controlled by the thrust bearings of No. 4 (center) main. The end play with new bearings must be .006 to .020 in. (0.152 to 0.508 mm). The maximum permissible end play with used bearings is .035 in. (0.89 mm).end by: a) install pistonsb) install flywheel housingc) install timing gear coverd) install crankshaft front seal wear sleevee) install crankshaft rear seal wear sleevef) install fuel injection pump housing and governor


Parts lock Mercury:

42202 1
 
42202 1 LOCK RING
1006201DB, 1006201PD, 1006201RB, 1006201VB, 1006211RD, 1008211RD, 1010207VB, 1011201DB, 1016207PD, 1016207RB, 1B25211UF
821971
LOCK, Throttle
821971 LOCK, Throttle
1006201PD, 1006201RB, 1006201VB, 1006211RD, 1008211RD, 1010207VB, 1016207PD, 1016207RB, 1016207SB, 10202014D, 1020201VB, 1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1040213YL, 1041312UB, 10432037D, 1043203VD, 1A30302ZB, 1A41412ZB, 1B25203ZB, 1F08203V
Back to top