29359 Mercury LUBRICAP, GREASE FITTING


29359 LUBRICAP, GREASE FITTING Mercury 1020100, 1020202, 1040102, 1040206, 1040208, 1045205, 1075101, 1075202, 1075204, 1110100, 1110102, 1110204, 1115100, 1115503, 1115525, 1135100, 1150503, 1150625, 1200203, 1400100, 1402202, 1402205, 1500101, 1500205, 1650502, 1650503, 1800100, 1850503 LUBRICAP
29359 LUBRICAP, GREASE FITTING Mercury
Rating:
73

Buy LUBRICAP, GREASE FITTING 29359 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 23
 

Mercury entire parts catalog list:

1020100 1970
1020202 1972
1040102 1972,1973,1974
1040206 1976,1977,1978,1979
1040208 1978,1979
1045205 1975,1976,1977,1978,1979
1075101 1971,1975
1075202 1972,1973
1075204 1974,1975,1976,1977
1110100 1970,1971
1110102 1972,1973
1110204 1974,1975,1976,1977
1115100 1970,1971,1972
1115503 1973,1974,1976,1977
1115525 1985
1135100 1970,1971
1150503 1973,1974,1975,1976,1977,1985
1150625 1985
1200203 1973,1974,1975,1976,1977
1400100 1970,1971
1402202 1972,1973,1974
1402205 1975,1976,1977
1500101 1971,1972,1973,1974
1500205 1975
1650502 1972
1650503 1973,1974,1975
1800100 1970,1971,1972
1850503 1973,1974,1975

Information:

2. Remove the fuel lines (1) from the fuel injection pump to the valve cover base. Put caps or plugs on all connections to keep dirt out of the fuel lines. 3. Remove the wire (2) for the temperature indicator. Remove the hose clamps and remove the water outlet elbow (3).4. Disconnect the boost line at the aftercooler for the air fuel ratio control.5. Remove the flange for the heater hose at the front of the cylinder head. 6. Remove the bolts (4) that hold the valve cover base to the cylinder head and the timing gear housing. 7. Remove the valve cover base (5). 8. Remove the bolts that hold the cylinder head to the engine block. Install three 3/8"-16 NC forged eyebolts in the head as shown. Fasten a hoist to the cylinder head (6). Remove the cylinder head. Weight of the cylinder head is 400 lb. (181.4 kg). 9. Remove the head gasket and water directors from the spacer plate. Use six 3/8"-16 NC forcing screws to remove the spacer plate (7) from the engine. Remove the gasket from under the spacer plate.10. Make certain the top of the block is not damaged and is clean.Install Cylinder Head And Spacer Plate
Always make a replacement of the gasket under the spacer plate. Do not put any adhesive on the spacer plate or gasket. Make certain the top of the block and the spacer plate are clean and dry before installation of the gasket or spacer plate. 1. Put a new gasket in position on the cylinder head. Put the spacer plate (1) in position on the gasket. Install the O-ring seal (2) as shown. 2. Install the cylinder head gasket (3) on the spacer plate. Install the water directors. Install two 3/4"-16 NF guide pins (4) in the cylinder head as shown. 3. Fasten a hoist to the cylinder head (5) as shown. Put it in position on the guide pins and lower it on to the cylinder block. Weight of the cylinder head assembly is 400 lb. (181.4 kg). 4. Put clean engine oil on the threads of the bolts for the cylinder head. Install the bolts and tighten them as follows: 1: Tighten all bolts in number sequence to 200 lb.ft. (271.2 N m).2: Tighten all bolts in number sequence to 330 10 lb.ft. (447.4 13.6 N m).3: Again tighten (hand torque only) all bolts in number sequence to 330 10 lb.ft. (447.4 13.6 N m). 5. Put the valve cover base (6) in position on the cylinder head. Install the bolts that hold it to the cylinder head and timing gear housing. 6. Put the fuel lines (7) in position on the engine. Tighten the fuel line to a torque of 30 5 lb.ft. (40.8 6.8 N m).7. Install the water outlet elbow and the hose clamps that connect it to the oil cooler. Install the wire for the temperature indicator. Install the boost line for the fuel ratio control at the aftercooler. Install the flange for the heater hose at the front of the engine head.8. Fill the engine coolant to the correct level. See LUBRICATION and MAINTENANCE guide for the correct level.end by:a) install camshaftsb) install exhaust manifoldc) install support


Parts lubricap Mercury:

53216
Back to top