898101070 Mercury MOUNT, Rubber-Fuel Filter


898101070 MOUNT, Rubber-Fuel Filter Mercury 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ MOUNT
898101070 MOUNT, Rubber-Fuel Filter Mercury
Rating:
48

Buy MOUNT, Rubber-Fuel Filter 898101070 Mercury genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$10.39
 

28-09-2017
.3[0.00] pounds
MERCURY: MERCURY
New Mercury Mercruiser Quicksilver Oem Part # 898101070 Mount
Number on catalog scheme: 22
 

Compatible models:

Mercury entire parts catalog list:

1A25203FK 2006
1A25203FL 2006
1A25311FK 2006
1A25312FK 2006
1A30413KZ 2010

Information:

1. Loosen adjustment screws (3) to have maximum valve clearance.2. Remove six bolts (2) and washers that hold the rocker shaft in position.3. Remove rocker shaft assembly (1). 4. Remove push rods (4). 5. Remove O-ring seal (5) from rear support bracket. The O-ring seal (5) must be installed new each time the head bolt is removed from the rear support bracket.Install Rocker Shaft And Push Rods
1. Install a new O-ring seal in the rear support bracket of rocker shaft. 2. Install push rods (1).3. Put rocker shaft (2) in position on the cylinder head.
The dowel pins (3) on each end of the rocker shaft and arms must be in alignment with the holes in the cylinder head. If the pins and holes are not in alignment when the bolts are tightened, damage to the rocker shaft and arms can be the result.
4. Put 5P3931 Anti-Seize Compound on the threads of the bolts that hold the rocker shaft in position. Install the six bolts and washers. 5. Tighten all bolts (4), (5), (6), (7), (8), (9) in number sequence to a torque of 115 lb.ft. (155 N m). Tighten bolts again in number sequence to a torque of 185 13 lb.ft. (250 17 N m). Last, tighten the bolts again (hand turn only) in number sequence to a torque of 185 13 lb.ft. (250 17 N m).6. Make adjustments until the intake valve clearance is .015 in. (0.38 mm) and the exhaust valve clearance is .025 in. (0.64 mm).end by: a) install valve coverDisassemble Rocker Shaft
start by: a) remove rocker shaft and push rods 1. Remove O-ring seal (1) from the rear support bracket. A replacement of the O-ring seal must be made each time the head bolt is removed from the rear support bracket. 2. Remove retainer ring (6), washer (5), spring (4) and washer (3) from each end of rocker shaft. Remove rocker arm (2). 3. Remove pin from rear support bracket with a hammer and punch. Remove rear support bracket (7) from shaft.4. Remove remainder of rocker arms, springs, washers and brackets.5. Check the bore in the bearings for the rockers. The diameter with new bearings must be .7263 .0005 in. (18.448 0.013 mm). The maximum permissible clearance between the shaft and bearings (worn) must not be more than .008 in. (0.20 mm).6. Check the condition of the plugs in the ends of the rocker shaft. If the plugs have damage, use new parts for replacement. Plugs that have damage can cause loss of oil pressure.Assemble Rocker Shaft
1. Install rocker arms (5), brackets (1), washers (4) and springs (2) on the rocker shaft.2. Install rear support bracket (6) on rocker shaft. Make sure hole in rear support bracket is in alignment with hole in rocker shaft.3. Put pin (3) in position in the bracket. 4. Install pin (3) through bracket and shaft with a hammer.5. Pin (3) must extend .378 in. (9.60 mm) above the bracket. 6. Install O-ring seal (7) in the rear support bracket. Install rocker arm (8), washer, spring, washer and retainer ring on the rocker shaft.7. Install the plugs in each end of the rocker shaft if they were removed.8. Put clean engine oil on all the parts after the rocker shaft is assembled.


Parts mount Mercury:

853743 7
MOUNT, Rubber
853743 7 MOUNT, Rubber
1025207FL, 1025207FM, 1025217FL, 1025217FM, 1030201FL, 1030201YL, 1030211FL, 1030271HL, 1030302FL, 1030312FL, 1030A01FL, 1030A11FL, 1031207ZF, 1040203FL, 1040203YL, 1040213YL, 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ, 1B04201FB, 1F04201W
851837
MOUNT, Rubber
851837 MOUNT, Rubber
1040203FL, 1040203YL, 1040213YL, 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ, 1F15211HM
853771 2
 
853771 2 MOUNT
1040203FL, 1040203YL, 1040213YL, 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ, 1F25A17DM
898101158
MOUNT, Rubber
898101158 MOUNT, Rubber
1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ, 1F15211HM
898101223
MOUNT, Rubber
898101223 MOUNT, Rubber
1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ
898101242
MOUNT, Rubber, Upper
898101242 MOUNT, Rubber, Upper
1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ
Back to top