17172 Mercury NUT, PLATE BOLT


17172 NUT, PLATE BOLT Mercury 1004137, 1015203FL NUT
17172 NUT, PLATE BOLT Mercury
Rating:
83

Buy NUT, PLATE BOLT 17172 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 29
 

Compatible models:

Mercury entire parts catalog list:

1004137 1987,1988,1989
1015203FL 2006

Information:

start by:a) remove crankshaft vibration damper Any time the crankshaft seal is removed from the wear sleeve, a new sleeve and seal must be installed as a unit. If the seal is put back on the sleeve, the seal will leak. 1. Remove the bolts from adapter (1) and install two 5/16" - 13 NC forcing screws in the adapter to remove it from the drive housing. 2. Remove O-ring seal (3) and crankshaft seal (2) from adapter (1). 3. Install tool (B) in adapter bore as shown.4. Install tool (A) between tool (B) and wear sleeve (4). Turn tool (A) until the edge of the tool makes a flat plate (crease) in the wear sleeve. Do this several places around the wear sleeve until the sleeve can be removed from the end of the crankshaft by hand.Install Crankshaft Front Seal And Wear Sleeve
Any time the crankshaft seal is removed from the wear sleeve, a new sleeve and seal must be installed as a unit. If the seal is put back on the sleeve, the seal will leak. 1. Install adapter (3) on tooling (A) as shown.
If the crankshaft seal and wear sleeve come apart during installation, the seal and sleeve become scrap and a new seal and sleeve must be used as a replacement.
The front seal and wear sleeve can not be exchanged with the rear seal and wear sleeve. There are grooves in the sealing lip of the seals that direct the oil back into the crankcase as the crankshaft turns. An exchange of front and rear seals would pump the oil out of the crankcase.2. Put crankshaft seal (1) and wear sleeve (2) as a unit in position on adapter (3). Make sure the lip of the seal is up as shown. 3. Install tool (B) over the studs of tooling (A). Install nuts (C) and tighten the nuts evenly until the seal is against the bottom of the adapter bore.4. Remove nuts (C), tool (B) and tooling (A) from the adapter. Do not put engine oil on the lip of the seal during installation. Lubrication of the seal at installation can be a wrong indication for linkage at a later time.5. Put clean engine oil on the O-ring seal and install the seal on the adapter. 6. Install tooling (D) on the end of the crankshaft.7. Install guide bolts (E) in the drive housing. Put adapter (3) in position on guide bolts (E) and over tooling (D). Make sure the wear sleeve makes contact with the end of the crankshaft. 8. Install tool (B) over the small outside diameter of tool (F) until tool (B) is against the shoulder on tool (F).9. Install tooling (B) and (F) as a unit on the guide bolts and over the locator.10. Put clean engine oil on the face of nut (G) and install nut (G) on the locator. Tighten nut (G) until the wear sleeve and adapter are in position.11. Remove the tooling from the engine. 12. Install bolts (4) to hold adapter (3) in position.end by:a) install crankshaft vibration damper


Parts nut Mercury:

16081
 
16081 NUT, RECTIFIER SCREW
1004137, 1004201FB, 1004201JK, 1004201VB, 1006201AK, 1006201FK, 1008201YM, 1015203FL, 1015203YL, 1025207FL, 1025207FM, 1025217FL, 1025217FM, 1030201FL, 1030201YL, 1030211FL, 1030271HL, 1030302FL, 1030312FL, 1030A01FL, 1030A11FL, 1031207ZF, 1040203FL,
16271
 
16271 NUT, CHECK VALVE SCREW
1004137, 1004201FB, 1004201JK, 1004201VB, 1006201FK
16825
 
16825 NUT, MOUNT
1004137, 1025207FL, 1025207FM, 1025217FL, 1025217FM, 1030201FL, 1030211FL, 1030271HL, 1030302FL, 1030312FL, 1030A01FL, 1030A11FL
16071
 
16071 NUT, FLYWHEEL
1004137, 1004201FB, 1004201JK, 1004201VB, 1006201AK, 1006201FK, 1008201YM, 1B08201DB, 1F04201WB
853722 5
 
853722 5 NUT
1006201AK, 1006201FK, 1008201YM, 1015203FL, 1015203YL, 1025207FL, 1025207FM, 1025217FL, 1025217FM, 1030201FL, 1030201YL, 1030211FL, 1030271HL, 1030302FL, 1030312FL, 1030A01FL, 1030A11FL, 1031207ZF, 1040203FL, 1040203YL, 1040213YL, 1B08201DB, 1F25A17D
853722 16
 
853722 16 NUT
1015203FL, 1015203YL, 1030201YL, 1031207ZF, 1040203FL, 1040203YL, 1040213YL, 1B08201DB, 1F15207DM, 1F15207FM, 1F25A17DM
853722 11
 
853722 11 NUT
1015203FL, 1015203YL, 1025207FL, 1025207FM, 1025217FL, 1025217FM, 1030201FL, 1030201YL, 1030211FL, 1030271HL, 1030302FL, 1030312FL, 1030A01FL, 1030A11FL, 1031207ZF, 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ, 1B08201DB, 1F15207DM, 1F15207F
Back to top