16177 Mercury "O" RING, UPPER CAM ROD


16177 "O" RING, UPPER CAM ROD Mercury 1004137 O
16177 "O" RING, UPPER CAM ROD Mercury
Rating:
93

Buy "O" RING, UPPER CAM ROD 16177 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 16
 

Compatible models:

1004137   Mercury

Mercury entire parts catalog list:

1004137 1987,1988,1989

Information:

Start By:a. remove crankshaft vibration damperFluid Spillage Containment
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to "Tools And Shop Products Guide", NENG2500 for tools and supplies suitable to collect and contain fluids in Caterpillar machines. Dispose fluids according to local regulations and mandates. Any time the crankshaft seal is removed from the wear sleeve, a new sleeve and seal must be installed as a unit. If the seal is put back on the sleeve, the seal will leak. 1. Remove the bolts from adapter (1) and install two 5/16-13 NC Forcing Screws in the adapter to remove it from the drive housing. 2. Remove O-ring seal (3) and crankshaft seal (2) from adapter (1). 3. Install Tool (B) in adapter bore as shown.4. Install Tool (A) between Tool (B) and wear sleeve (4). Turn Tool (A) until the edge of the tool makes a flat plate (crease) in the wear sleeve. Do this several places around the wear sleeve until the sleeve can be removed from the end of the crankshaft by hand.Install Crankshaft Front Seal & Wear Sleeve
Any time the crankshaft seal is removed from the wear sleeve, a new sleeve and seal must be installed as a unit. If the seal is put back on the sleeve, the seal will leak. 1. Install adapter (3) on Tooling (A) as shown.
If the crankshaft seal and wear sleeve come apart during installation, the seal and sleeve become scrap and a new seal and sleeve must be used as a replacement.
The front seal and wear sleeve can not be exchanged with the rear seal and wear sleeve. There are grooves in the sealing lip of the seals that direct the oil back into the crankcase as the crankshaft turns. An exchange of front and rear seals would pump the oil out of the crankcase.2. Put crankshaft seal (1) and wear sleeve (2) as a unit in position on adapter (3). Make sure the lip of the seal is up as shown. 3. Install Tool (B) over the studs of Tooling (A). Install nuts (C) and tighten the nuts evenly until the seal is against the bottom of the adapter bore.4. Remove nuts (C), Tool (B) and Tooling (A) from the adapter. Do not put engine oil on the lip of the seal during installation. Lubrication of the seal at installation can be a wrong indication for linkage at a later time.5. Put clean engine oil on the O-ring seal and install the seal on the adapter. 6. Install Tooling (D) on the end of the crankshaft.7. Install guide bolts (E) in the drive housing. Put adapter (3) in position on guide bolts (E) and over Tooling (D). Make sure the wear sleeve makes contact with the end of the crankshaft. 8. Install Tool (B) over the small outside diameter of Tool (F) until Tool (B) is against the shoulder on Tool (F).9. Install Tooling (B) and (F) as a unit on the guide bolts and over the locator.10. Put clean engine oil on the face of nut (G) and install nut (G) on the locator. Tighten nut (G) until the wear sleeve and adapter are in position.11. Remove the tooling from the engine. 12. Install bolts (4) to hold adapter (3) in position.End By:a. install crankshaft vibration damper


Parts o Mercury:

16259
 
16259 "O" RING, FLOAT BOWL
1004137, 1004201FB, 1004201JK, 1004201VB, 1006201AK, 1006201FK, 1008201YM
16131
 
16131 "O" RING, PROPELLER SHAFT HOUSING
1002201FM, 1002201VB, 1003201NK, 1004137, 1004201FB, 1004201JK, 1004201VB, 1006201AK, 1006201FK, 1008201YM, 1040203FL, 1040203YL, 1040213YL, 1B04201FB, 1B08201DB, 1F02201HM, 1F04201WB
812641
"O" RING
812641 "O" RING
1004137, 1004201FB, 1004201JK, 1004201VB, 1006201FK, 1008201YM
16109
 
16109 "O" RING, STARTER ROPE
1004137, 1006201AK, 1015203FL, 1015203YL, 1025207FL, 1025207FM, 1025217FL, 1025217FM, 1030201FL, 1030201YL, 1030211FL, 1030271HL, 1030302FL, 1030312FL, 1030A01FL, 1030A11FL, 1031207ZF
16181
 
16181 "O" RING, SHIFT LEVER
1004137, 1004201FB, 1004201JK, 1004201VB, 1B04201FB, 1F04201WB
16178
 
16178 "O"RING, LOWER CAM ROD
1004137, 1004201FB, 1004201JK, 1004201VB, 1006201AK, 1006201FK, 1008201YM, 1B04201FB, 1B08201DB, 1F04201WB
Back to top