31411 Mercury OIL SEAL (39)(40)


31411 OIL SEAL (39)(40) Mercury 1040100, 1040102, 1045205, 1075101 OIL
31411 OIL SEAL (39)(40) Mercury
Rating:
83

Buy OIL SEAL (39)(40) 31411 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 22
 

Compatible models:

Mercury entire parts catalog list:

Information:

4. Disconnect heater hose (1) from the housing assembly.5. Remove the hose from the housing assembly on the water pump to the inlet elbow on the radiator.6. Remove bolts (2) that hold the housing assembly in position. Remove housing assembly (3). 7. Remove tube assembly (5).8. Remove four bolts (4). 9. Remove nuts (6) from behind the water pump. Remove water pump (7).Install Water Pump
1. Check the condition of the seal in the housing assembly for the water pump. If the seal has damage, use new parts for replacement. 2. Put water pump (1) in position on the timing gear cover. Install nuts (2) that hold it.3. Install four bolts (3).4. Install the tube assembly to the water temperature regulator housing on the right side of the machine. 5. Install housing assembly (5) over the water pump. Install the bolts that hold it.6. Install the hose from the water pump to the inlet elbow on the radiator.7. Connect heater hose (4) to the housing assembly.8. Install the vee belt set for the fan.9. Install the panel over the water pump. The location of the panel is on the left side of the machine.10. Fill the cooling system with coolant to the correct level. See Maintenance Guide. Disassemble Water Pump
Start By:a. remove water pump 1. Remove O-ring seal (1) from adapter (2).2. Remove adapter (2) with a screwdriver. Remove the seal from the edge of adapter (2).3. Remove bolt (3) and washer. 4. Remove impeller (4) from the water pump housing with tooling (A). 5. Remove seal assembly (5). Remove ring and seal (6). 6. Remove the bolt and washer that hold gear (7) on the water pump shaft.7. Remove gear (7) with tooling (B).8. Remove bolts and retainer (9).9. Remove O-ring seal (8). 10. Remove shaft (10) and bearings as a unit.11. Remove bearing (11), spacer (12) and bearing (13) from shaft (10).12. Remove lip type seal from the gear side of the water pump. Remove ring and seal from the impeller side of the water pump.Assemble Water Pump
1. Put clean engine oil on the lip seal (1). Install seal (1) as shown with tooling (A). 2. Install bearing (4), spacer (3) and bearing (5) on shaft (2). Install shaft (2) in the pump housing. 3. Install retainer (7) and O-ring seal (8).4. Install gear (6). Install the washer and bolt that hold gear (6) to shaft (2).
Clean water only is permitted for use as a lubricant for assistance at installation. Do not damage or put hands on the wear surface of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
5. Put ceramic ring (10) in position in the rubber seal (9). Use hand pressure and the tool (which is with the replacement ring) to install the ceramic ring in the housing.6. Remove spring (12) from seal assembly (11). Use hand pressure and the tool (which is with the replacement ring) to install the seal (11) assembly. Push seal assembly on the shaft until the seal face makes light contact.7. Install spring (12) on the shaft. 8. Install impeller (14) and the washer and bolt (13) that hold the impeller to the pump shaft. Tighten the bolt to a torque of 39 3 N m (28 2 lb ft). Make an air pressure test of the seal at 140 kPa (20 psi). 9. Put clean engine oil on the O-ring seals (15). Install the O-ring seals on adapter (16).10. Install adapter (16) in the pump housing with the notch in alignment with dowel (17).End By:a. install water pump


Parts oil Mercury:

56397
 
56397 OIL SEAL (40)
1003203, 1003209, 1005200, 1040100, 1040102, 1045205, 1075101, 1075202, 1110100, 1110102
30696
 
30696 OIL SEAL
1005200, 1007208, 1007209, 1010208, 1020100, 1020202, 1020208, 1040100, 1040102, 1045205, 1075101, 1075202, 1075204, 1110100, 1110102, 1110204, 1200203
30900
 
30900 OIL SEAL
1005200, 1007208, 1007209, 1010208, 1040100, 1040102, 1045205, 1075101, 1075202, 1075204, 1110100, 1110102, 1110204
30913
 
30913 OIL SEAL
1003203, 1003209, 1004200, 1005200, 1007208, 1007209, 1010208, 1040100, 1040102, 1040206, 1045205, 1075101, 1075202, 1075204, 1110100, 1110102, 1110204
30530
 
30530 OIL SEAL
1004200, 1040100, 1040102, 1040206, 1075101, 1075202, 1110100, 1110102
56741
 
56741 OIL SEAL, UPPER BEARING HOUSING
1075101, 1075202, 1110100, 1110102
66301
 
66301 OIL SEAL, UPPER BEARING HOUSING
1003203, 1003209, 1005200, 1007208, 1007209, 1010208, 10402139D, 1045205, 1050302SD, 1050312LD, 1055207DB, 1055207UD, 1055207VB, 1075204, 1110204, 1A40302FD, 1A40302HZ, 1A40303KZ, 1A40311FZ, 1A40311HZ, 1A40403HZ, 1A40412HZ, 1A41412ZB, 1A41452EZ, 1A41
66022
 
66022 OIL SEAL, BEARING CARRIER
1005200, 1006206, 1007208, 1007209, 1008211RD, 1010208, 1045205, 1075204, 1110204
Back to top