41470A12 OIL INJECTION WARNING MODULE ASSEMBLY Mercury
1175413LD, 1200413GD, 1220727
OIL
Price: query
Rating:
Mercury entire parts catalog list:
- DETONATION CONTROLLER-TEMPERATURE SENSOR » 41470A12
- DETONATION CONTROLLER-TEMPERATURE SENSOR » 41470A12
- DETONATION CONTROLLER-TEMPERATURE SENSOR » 41470A12
Information:
Illustration 1 g01927355
Typical example (1) Exhaust valve spring (2) Inlet valve spring
Table 1
Specifications for 298-4530 Spring and 326-7290 Spring    
Callout     Part Number     Part Name     Specification Description    
1     298-4530     Spring     The load for the exhaust valve spring is
285 to 315 N (64.07085 to 70.81515 lb).
The length of the exhaust valve spring is
31.5 mm (1.2402 inch).
The load for the exhaust valve spring is
337.9 to 373.5 N (75.96330 to 83.96654 lb).
The length of the exhaust valve spring is
21.5 mm (0.84646 inch).
The free length of the exhaust valve spring is
52.73 mm (2.07598 inch).    
2     326-7290     Spring     The load for the inlet valve spring is
161.5 to 178.5 N (36.30682 to 40.12859 lb).
The length of the inlet valve spring is
31.5 mm (1.2402 inch).
The load for the inlet valve spring is
389.5 to 430.5 N (87.5 to 97 lb).
The length of the inlet valve spring is
22.2 mm (0.87401 inch).
The free length of the inlet valve spring is
40.65 mm (1.60039 inch).    When the valve springs are replaced the valve springs must be replaced in pairs.Removal Procedure
Table 2
Required Tools    
Tool     Part Number     Part Description     Qty    
A     9U-6195     Valve Spring Compressor     1    
268-1969 Adapter     1    
276-1221 Head     1    
B (1)     9U-6198     Crankshaft Turning Tool     1    
B (2)     5P-7306     Housing     1    
5P-7305 Engine Turning Tool     1    
( 1 ) The Crankshaft Turning Tool is used on the front pulley.
( 2 ) This Tool is used in the aperture for the electric starting motor.Start By:
Remove the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod" for the correct procedure.Note: Either Tooling (B) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The following procedure should be adopted in order to remove the valve springs when the cylinder head is installed to the engine. Refer to Disassembly and Assembly, "Inlet and Exhaust Valves" for the procedure to remove the valve springs from a cylinder head that has been removed from the engine.Note: Ensure that the appropriate piston is at top dead center before the valve spring is removed. Failure to ensure that the piston is at top dead center may allow the valve to drop into the cylinder bore.
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Plug the apertures for the push rods in the cylinder head in order to prevent the entry of loose parts into the engine.
Illustration 2 g01978813
Follow Step 1.a through Step 1.h in order to remove the harness assemblies for the electronic unit injectors.
Place a temporary identification mark on connections (1) for harness assembly (3) for electronic unit injectors (2) .
Use a deep socket to remove connections (1) from electronic unit injectors (2) .
Cut cable straps (4) and remove the remaining sections of the cable straps from the cylinder head.
Disconnect plug (6) from harness assembly (3) .
Remove bolt (5) from harness assembly (3) .
Withdraw harness assembly (3) from the cylinder head.
Remove O-ring seal (7) from harness assembly (3) .
Repeat Step 1.a through Step 1.g in order to remove the remaining harness assemblies.
Il
Parts oil Mercury:
76868
76868 OIL SEAL, BEARING CARRIER
1050302SD, 1050312LD, 1070312BC, 1070717, 10754120D, 1075524, 1080500, 1080508, 1090520, 1090524, 1090528, 1100312BD, 1100412PD, 111047JHD, 1115473WD, 1115503, 1115520, 1115523, 1115525, 1115528, 11354120D, 1135412GD, 1135412MD, 1135412SD, 1135412VD,
76384
76384 OIL SEAL, SHIFT SHAFT BUSHING
1035204, 1040208, 1045217, 1050200, 1050312BC, 1060504, 1070312BC, 1070717, 1075524, 1080500, 1080508, 1090520, 1090524, 1090528, 1115520, 1115523, 1115525, 1115528, 1135412GD, 1135726, 1140520, 1140528, 1140629, 1150453BD, 1150453GD, 1150453JD, 1150
89238
89238 OIL SEAL
111047JHD, 1115473WD, 11354120D, 1135412GD, 1135412MD, 1135412SD, 1135412VD, 1135412WD, 1135473UD, 1135473VD, 1135473YD, 1135726, 1135D73CD, 1135D73FT, 1150413CD, 1150413FY, 1150413HF, 1150413HY, 1150413SD, 1150413VD, 1150413WD, 1150413ZD, 1150423FG,
16977
16977 OIL SEAL
1090524, 111047JHD, 1115473WD, 1115525, 11354120D, 1135412GD, 1135412MD, 1135412SD, 1135412VD, 1135412WD, 1135473UD, 1135473VD, 1135473YD, 1135726, 1135D73CD, 1135D73FT, 1150413CD, 1150413FY, 1150413HF, 1150413HY, 1150413SD, 1150413VD, 1150413WD, 115
816464
816464 OIL SEAL
1035207, 11354120D, 1150453BD, 1150453GD, 1150453JD, 1150625, 1150628, 1175413LD, 1175626, 1200628
815699
815699 OIL PUMP ASSEMBLY
11354120D, 1135412MD, 1135412SD, 1150413SD, 1150453JD, 1175413LD, 1175413MD, 1200412GD, 1200413GD, 1200628
41033
99443T