825197T Mercury OIL SEAL TOOL

Table 1
Required Tools
Tool Part Number Part Description Qty
A 421-5663 Lifting Eye Assembly 1
B 439-3938 Link Bracket 1
C 477-8634 Load Leveler Gp 1
D 422-8733 Jack Stand Gp 2
E 422-2352 Jack Stand Gp 2 Start By:
If equipped, remove the sweeps.
The Power Train Electric Drive System will contain hazardous voltage levels during machine operation and for a period of time after machine shutdown.Do not remove any covers that will expose energized electrical components while the engine is operating. Do not remove any covers that will expose the energized electrical components while the components remain energized following an engine shutdown.Do not perform any type of electrical maintenance on the orange hazardous voltage conductors or the power train components while the engine is operating.Do not perform any type of electrical maintenance on the orange hazardous voltage conductors or the power train components while the components remain energized following an engine shutdown.Always perform the safe shutdown and de-energizing procedure before performing electrical service on the Power Train Electric Drive System.Failure to follow these instructions could result in personal injury or death.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Personal injury can result from hot coolant, steam, and alkali.At operating temperature, engine coolant is hot and under pressure. The radiator and all lines to heaters or the engine contain hot coolant or steam. Any contact can cause severe burns.Remove cooling system pressure cap slowly to relieve pressure only when engine is stopped and allow sufficient time for the cooling system to cool.Do not attempt to tighten hose connections when the coolant is hot, the hose can come off causing burns.Cooling System Coolant Additive contains alkali. Avoid contact with skin and eyes.
Personal injury can result from contact with refrigerant.Contact with refrigerant can cause frost bite. Keep face and hands away to help prevent injury.Protective goggles must always be worn when refrigerant lines are opened, even if the gauges indicate the system is empty of refrigerant.Always use precaution when a fitting is removed. Slowly loosen the fitting. If the system is still under pressure, release it slowly in a well ventilated area.Personal injury or death can result from inhaling refrigerant through a lit cigarette.Inhaling air conditioner refrigerant gas through a lit cigarette or other smoking method or inhaling fumes released from a flame contacting air conditioner refrigerant gas, can cause bodily harm or death.Do not smoke when servicing air conditioners or wherever refrigerant gas may be present.Use a certified recovery and recycling cart to properly remove the refrigerant from the air conditioning system.
Perform the electrical shutdown procedure. Refer to Operation and Maintenance Manual, "Electrical Shutdown and Voltage Discharge" for the correct procedure.
Turn the battery disconnect switch to the OFF position.
Remove the cab. Refer to Disassembly and Assembly, "Cab - Remove and Install" for the correct procedure.
Remove the clean emissions module. Refer to Disassembly and Assembly, "Clean Emissions Module - Remove and Install" for the correct procedure.
Drain the hydraulic oil. Refer to Operation and Maintenance Manual, "Hydraulic System Oil - Change" for the correct draining and filling procedures.
Drain the coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change" for the correct draining and filling procedures.
Turn the fuel valve to the OFF position.
Recover the refrigerant. Refer to Service Manual, SENR5664, "Air Conditioning and Heating R134a for All Caterpillar Machines" for the recovery and the charging procedure. Refer to Special Publication, "Dealer Service Tools Catalog", "Air Conditioning Tools" for the correct tools.
Illustration 1 g06330181
Typical Example
Cut cable straps (2) and position harness assembly (1) out of the way.
Cut cable straps (4) and position harness assembly (3) out of the way.
Illustration 2 g06330183
Typical Example
Attach a suitable lift