99443T Mercury OIL RESERVOIR


99443T OIL RESERVOIR Mercury 1175413LD, 1175413MD, 1200413GD, 1220727 OIL
99443T OIL RESERVOIR Mercury
Rating:
43

Buy OIL RESERVOIR 99443T Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 10
 

Compatible models:

Mercury entire parts catalog list:

1175413LD 1991
1175413MD 1992,1993,1994,1995
1200413GD 1989,1990
1220727 1987,1988

Information:

Start By:a. remove engine balancer group (3114 Engines)b. remove oil pump (3116 Engines) 1. Remove bolts (1), the washers and bearing cap (2). Remove the lower main bearing half from the cap.
If the crankshaft is turned in the wrong direction during upper main bearing half removal, the tab of the bearing will be pushed between the crankshaft and the cylinder block. This can cause result in damage to either or both the crankshaft and the cylinder block.
Both the center and two end main journals have no oil hole. To remove these upper main bearing halves, put a thin piece of soft material, (that will not damage the crankshaft journal), against the end of the bearing half, opposite the tab. Hit the bearing with the soft material until the tab of the bearing is free from the groove in the cylinder block.2. Remove the upper half of the main bearings as follows: a. Turn the crankshaft until Tool (A) can be installed in the crankshaft journal. Install Tool (A) as shown.b. Turn the crankshaft in the direction which will push the upper main bearing half out, tab end first.c. Check the condition of the main bearings. Refer to "Guideline For Reusable Parts, Main & Connecting Rod Bearings", Form No. SEBF8009 and SEBD0531 as guide for checking bearing condition. The following steps are for the installation of the crankshaft main bearings.3. Clean the bearing surfaces in the cylinder block for the main bearings. Apply clean engine oil on the upper main bearing half. Do not put oil on the back side of the bearing. Using Tool (A), install the upper main bearing half (bearings with the oil holes) in the cylinder block. Be sure the tab on the back side of the bearing engages with the groove in the cylinder block.4. Clean the bearing surface of the main bearing caps. Install the lower main bearing half in the main bearing cap. Be sure the tab on the back side of the bearing engages with the groove in the main bearing cap. Apply clean engine oil on the lower main bearing half. Do no put oil on the back side of the bearing.5. Install the main bearing caps as follows:
Install the main bearing caps with the sequence number to the right, 1 through 5 (for the 4 cylinder) and 1 through 7 (for the 6 cylinder), front to rear.
a. Put main bearing caps (2) in position in the cylinder block with the sequence numbers in the correct positions.b. Apply clean engine oil to the threads of the main bearing cap mounting bolts and on the washer contact faces.c. Install main bearing cap mounting bolts (1) and the washers. Tighten both bolts of each main bearing cap to a torque of 54 7 N m (40 5 lb ft).d. Tighten the bolts and additional 1/4 90 5 degrees ( turn). 6. Check the end play of the crankshaft with Tool (B). The end play of the crankshaft (3114) must be 0.07 to 0.29 mm (.003 to .011 in). The end play of the crankshaft (3116) must be 0.07 to 0.32 mm (.003 to .013 in).End By:a. install oil pump (3116 Engines)b. install engine balancer group (3114 Engines)


Parts oil Mercury:

76868
 
76868 OIL SEAL, BEARING CARRIER
1050302SD, 1050312LD, 1070312BC, 1070717, 10754120D, 1075524, 1080500, 1080508, 1090520, 1090524, 1090528, 1100312BD, 1100412PD, 111047JHD, 1115473WD, 1115503, 1115520, 1115523, 1115525, 1115528, 11354120D, 1135412GD, 1135412MD, 1135412SD, 1135412VD,
76384
 
76384 OIL SEAL, SHIFT SHAFT BUSHING
1035204, 1040208, 1045217, 1050200, 1050312BC, 1060504, 1070312BC, 1070717, 1075524, 1080500, 1080508, 1090520, 1090524, 1090528, 1115520, 1115523, 1115525, 1115528, 1135412GD, 1135726, 1140520, 1140528, 1140629, 1150453BD, 1150453GD, 1150453JD, 1150
89238
 
89238 OIL SEAL
111047JHD, 1115473WD, 11354120D, 1135412GD, 1135412MD, 1135412SD, 1135412VD, 1135412WD, 1135473UD, 1135473VD, 1135473YD, 1135726, 1135D73CD, 1135D73FT, 1150413CD, 1150413FY, 1150413HF, 1150413HY, 1150413SD, 1150413VD, 1150413WD, 1150413ZD, 1150423FG,
16977
 
16977 OIL SEAL
1090524, 111047JHD, 1115473WD, 1115525, 11354120D, 1135412GD, 1135412MD, 1135412SD, 1135412VD, 1135412WD, 1135473UD, 1135473VD, 1135473YD, 1135726, 1135D73CD, 1135D73FT, 1150413CD, 1150413FY, 1150413HF, 1150413HY, 1150413SD, 1150413VD, 1150413WD, 115
815699
 
815699 OIL PUMP ASSEMBLY
11354120D, 1135412MD, 1135412SD, 1150413SD, 1150453JD, 1175413LD, 1175413MD, 1200412GD, 1200413GD, 1200628
41470A12
 
41470A12 OIL INJECTION WARNING MODULE ASSEMBLY
1175413LD, 1200413GD, 1220727
41033
 
41033 OIL PUMP
1220727
41470A25
OIL INJECTION WARNING MODULE
41470A25 OIL INJECTION WARNING MODULE
1150413SD, 1150413VD, 1175413MD
Back to top