72856 Mercury PIN, TOP COWL CATCH


72856 PIN, TOP COWL CATCH Mercury 1007208, 1007209, 1010208, 1075204, 1110204 PIN
72856 PIN, TOP COWL CATCH Mercury
Rating:
58

Buy PIN, TOP COWL CATCH 72856 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 10
 

Compatible models:

Mercury entire parts catalog list:

1007208 1978
1007209 1979,1980,1981,1982,1983,1984,1985
1010208 1978
1075204 1974,1975,1976,1977
1110204 1974,1975,1976,1977

Information:


Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     8S-2264     Puller Gp     3    Start By:
Remove fuel injection linesNote: Refer to Specifications, ""Engine Design"" for non-specified engine torques.
Illustration 1 g03351476
Remove fuel injection pump drive gear access cover (1) from front housing (2). Note: The cover is secured with adhesive sealant. Use a scraper to separate the cover from the gear case.
Illustration 2 g03349227
Note: After marking the position of the fuel injection pump drive gear (3) , do not rotate the engine crankshaft. Rotating the crankshaft will cause the fuel injection pump to become misaligned.
Place a mark on the fuel injection pump drive gear (3) and the idler gear for installation purposes. Loosen center nut (4) and back out to the end of the fuel injection pump shaft. DO NOT loosen the four bolts (5) that hold the fuel injection pump gear to the hub.
Illustration 3 g03384642
Note: Do not loosen or remove the four bolts (5) retaining the fuel injection pump drive gear (3) to the fuel injection pump hub (3A). Do not disassemble the fuel injection pump drive gear from the hub. Correct fuel injection timing will be difficult or next to impossible to achieve.
Illustration 4 g03349237
Install Tooling (A) onto the end of the fuel injection pump shaft nut (4). Loosen the pump drive gear (3) from the shaft, remove Tooling (A) and remove nut and washer (4) .Note: Fuel injection pump drive gear (3) can be removed from the gear case, however, would be best to let the gear remain in the gear housing.
Illustration 5 g03349431
Locate and highlight the timing mark (9) on the base of fuel injection pump (6) for installation purposes. Make a corresponding mark on the gear case. Unplug the stop solenoid harness assembly. Remove lube oil line (7) from the fuel injection pump and the block assembly. Remove mounting nuts (8) and fuel injection pump (6). Installation Procedure
Table 2
Required Tools    
Tool    Part Number    Part Description    Qty    
B         Loctite 593 Silicone Sealer        
Illustration 6 g03353182
Position fuel injection pump (6) into the housing and the pump drive gear. Install nuts (8). Line up timing marks (9) if the old fuel injection pump is being reused. If new fuel injection pump is being installed, refer to Testing and Adjusting, "Fuel Injection Timing - Check/Adjust" for the correct fuel injection timing procedures. Install lube oil line (7). Tighten nut (8) to a torque of 23 to 28 N m (204 to 248 lb in).
Illustration 7 g03349475
Make sure that fuel injection pump drive gear (3) is aligned with the idler gear using the reference marks made earlier. Install the washer and nut (4). Tighten nut (4) to a torque of 59 to 69 N m (44 to 51 lb ft) while holding the crankshaft pulley bolt with a socket wrench to prevent the crankshaft from turning.
Illustration 8 g03351683
Apply Tooling (B) on mating surface of cover (1). Install cover (1) on front housing (2). End By: Install fuel injector lines


Parts pin Mercury:

25319
 
25319 PIN, ROLL - HANDLE TO COWL LATCH ROD
1005200, 1007208, 1007209, 1010208, 1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040102, 1040213YL, 1041312UB, 10432037D, 1043203DD, 1043203VD, 1043213DD, 1043302DD, 1043411DD, 1043412DB, 1043412DD, 1045205, 1050302DB, 1050302FB, 1050302FD
46912
 
46912 PIN, DOWEL - CRANKCASE TO CYLINDER BLOCK
1007208, 1010208, 1040102, 1040206, 1040208, 1045205, 1075204, 1080500, 1080508, 1090520, 1090528, 1110204, 1115520, 1115523, 1115528, 1140520, 1140528, 1140629, 1150503, 1150538, 1150625, 1402205, 1500206, 1650502, 1650503, 1700507, 1850503, 1850506
46152
 
46152 PIN, THROTTLE HANDLE
1005200, 1007208, 1010208, 1020208, 1040102, 1045205, 1075204, 1110204, 1200203
27088
 
27088 PIN, BALL GEAR TO THROTTLE SHAFT
1005200, 1007208, 1010208, 1020202, 1020208, 1040102, 1045205, 1075202, 1075204, 1110102, 1110204, 1200203
68436
 
68436 PIN, BALL GEAR TO UNIVERSAL JOINT
1040102, 1075204, 1110204, 1200203
65855
 
65855 PIN, REED STOP
1007208, 1007209, 1010208, 1020208, 10402139D, 1045217, 1050200, 1050312BC, 1060504, 1070500, 1075204, 1110204, 1200203, 1500205, 1500206, 1650503, 1650506, 1700507
76207
 
76207 PIN, ROLL - THROTTLE CONTROL LEVER TO CONTROL SHAFT
1007208, 1007209, 1010208, 1075204, 1110204
77564
 
77564 PIN, BALL GEAR TO UNIVERSAL JOINT
1007208, 1010208, 1020208, 1045205
Back to top