82151M PIN Mercury
1225F23AK
PIN
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$390.00
19-05-2022
-: -
Replacement Parts 82151M KKyosho Flysky Noble NB4 TX Mini-Z EVO 2.4GHz Transmitter w/2 Receivers KYO82151M
82151M O82151M YO82151M KYO82151 KYO82151M KKyosho Flysky Noble NB4 TX Mini-Z EVO 2.4GHz Transmitter w/2 Receivers KYO82151M
82151M O82151M YO82151M KYO82151 KYO82151M KKyosho Flysky Noble NB4 TX Mini-Z EVO 2.4GHz Transmitter w/2 Receivers KYO82151M
$68.78
13-07-2024
4.75[2.14] pounds
Amazon.com
Cardone 82-151M New Power Window Lift Regulator
Cardone Stand alone window lift regulator, provides a more cost efficient solution to fixing your vehicle || O.E.M. design flaws are identified and corrected for long lasting performance || Meets or exceeds O.E.M. performance || Each unit is 100% new, providing reliable window lift operation || Guaranteed fit, form and function
Cardone Stand alone window lift regulator, provides a more cost efficient solution to fixing your vehicle || O.E.M. design flaws are identified and corrected for long lasting performance || Meets or exceeds O.E.M. performance || Each unit is 100% new, providing reliable window lift operation || Guaranteed fit, form and function
Compatible models:
1225F23AK
Mercury
Mercury entire parts catalog list:
Information:
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Lifting Bracket 1
B - Guide Stud
(M10 x 1.25 by 80 mm) 2 Start By:
Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install" for the correct procedure.
Remove the primary speed/timing sensor. Refer to Disassembly and Assembly, "Primary Engine Speed/Timing Sensor - Remove and Install" for the correct procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g03795183
Install Tooling (A) and a suitable lifting device to flywheel (2). The weight of the flywheel is approximately 42 kg (93 lb).
Remove two bolts (1) from Positions (X) on the flywheel.
Install Tooling (B) in Positions (X) on the flywheel.
Remove the remaining bolts (1) and remove flywheel (2).Note: A roll pin (3) is located between the crankshaft and the flywheel.
Inspect ring gear (4) and flywheel (2) for wear or damage. If the ring gear or the flywheel is worn or damaged, use new parts for replacement.
Illustration 2 g03795192
To remove ring gear (4) from flywheel (2), place the flywheel on a suitable support. Use a hammer and a punch (5) to remove the ring gear from the flywheel.Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A - Lifting Bracket 1
B - Guide Stud
(M10 x 1.25 by 80 mm) 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been heated.
Illustration 3 g03795238
If the ring gear was removed, follow Steps 1a through 1c to install ring gear (4) to flywheel (2).
Identify the orientation of the new ring gear to install the ring gear correctly onto the flywheel.Note: The chamfered side of Gear Teeth (Y) must face toward the starting motor when the flywheel is installed. The chamfered will ensure the correct engagement of the starting motor.
Heat ring gear (4) in an oven to a maximum temperature of 150°C (302°F) prior to installation.Note: Do not use a torch to heat the ring gear.
Ensure that ring gear (4) orientation is correct and quickly install the ring gear onto flywheel (2).
Illustration 4 g03795183
Thoroughly clean the flywheel housing. Inspect the crankshaft rear seal for leaks. If crankshaft rear seal has any oil leaks, replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove and Install" for the correct procedure.
Install Tooling (B) to Positions (X) in the crankshaft.
Install Tooling (A) and a suitable lifting device to flywheel (2). The weight of the flywheel is approximately 42 kg (93 lb).
Position flywheel (2) onto Tooling (B).Ensure that roll pin (3) is installed to the crankshaft and that the roll pin is free from damage. Align the hole in the flywheel with the roll pin in the crankshaft.
Install bolts (1) finger tight.
Remove Tooling (B) and install the two remaining bolts (1).
Use a suitable tool to prevent flywheel (2) from rotating. Tighten bolts (1) to a torque of 74 N m (54 lb ft).
Remove Tooling (A) and the lifting device from the flywheel.End By:
Install the primary speed/timing sensor. Refer to Disassembly and Assembly, "Primary Engine Speed/Timing Sensor - Remove and Install" for the correct procedure.
Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install" for the correct procedure.
Parts pin Mercury:
23784
23784 PIN, DOWEL - CRANKCASE TO CYLINDER BLOCK
1020100, 1020202, 1020208, 1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1035204, 1035207, 1040200, 1040208, 1040213YL, 1041312UB, 10432037D, 1043203DD, 1043203VD, 1043213DD, 1043302DD, 1043411DD, 1043412DB, 1043412DD, 1050302DB, 1050302FB,
82364M
82364M PIN-DOWEL
1115F13CC, 1115F13FF, 1115F13YD, 1225F23AK, 1B75412CF, 1B75413DF, 1F08203VF, 1F08261RF, 1F10203VD, 1F10352VD, 1F13203FB, 1F15201UD, 1F75411WD
804113
82149M
887793
888663
825087 1
888210