95218017 Mercury PIN, Spring


95218017 PIN, Spring Mercury 1040203FL, 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ, 1B08201DB, 1F15211HM PIN
95218017 PIN, Spring Mercury
Rating:
33

Buy PIN, Spring 95218017 Mercury genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$270.50
 

15-07-2022

-: -
Hirschmann 95218017, Silicone Peroxide Tube 8mm ID, 1.6mm WT
$9.11
 

30-12-2023
0.0154[0.01] Pounds
US: Boating Accessories
New Mercury Mercruiser Quicksilver Oem Part # 17-95218017 Spring Pin
Mercury Marine
Number on catalog scheme: 38
 

Mercury entire parts catalog list:

1040203FL 2006
1A25203FK 2006
1A25203FL 2006
1A25311FK 2006
1A25312FK 2006
1A30413KZ 2010
1B08201DB 2005,2006
1F15211HM 2006,2008

Information:

3. Remove cylinder liners (1) with Tool (A).4. Remove the O-ring seals and filler band from each of the cylinder liners.Install Cylinder Liners
1. Clean cylinder liners (3) and the liner bores in the cylinder block.2. Install the cylinder liners in the block without the O-ring seals or filler bands.3. Check the cylinder liner projection as follows:a. Install the S1589 Bolts (2) and 1S379 Washers of Tool (B) on the cylinder block next to each liner. Tighten the bolts evenly, in four steps: 14 N m (10 lb ft), 35 N m (25 lb ft), 70 N m (52 lb ft) and 95 N m (70 lb ft).b. Put the adapter plate on top of the liner, and install the remainder of Tool (B). Tighten the 1D4595 Bolts (1) evenly in four steps: 7 N m (5 lb ft), 20 N m (15 lb ft), 35 N m (25 lb ft) and 70 N m (52 lb ft).c. Check to be sure the distance from the bottom edge of the crossbar to the top of the cylinder block is the same on both sides of the liner.d. Check the cylinder liner projection with Tool (C) at four locations around the liner.e. Liner projection must be 0.033 to 0.175 mm (.0013 to .0069 in). Measurements on the same liner must not be different by more than 0.05 mm (.002 in). Average measurements between liners next to each other must not be different by more than 0.05 mm (.002 in). The maximum permissible difference between average projection of all cylinder liners is 0.10 mm (.004 in). If the liner is turned in the bore, it can make a difference in the liner projection.4. If the projection is not 0.033 to 0.175 mm (.0013 to .0069 in), check the thickness of the following parts: spacer plate, spacer plate gasket and cylinder liner flange. The thickness of the spacer plate must be 9.970 0.025 mm (.3925 .0010 in). The thickness of the spacer plate gasket must be 0.208 0.025 mm (.0082 .0010 in). The thickness of the cylinder liner flange must be 10.282 0.020 mm (.4048 .0008 in). If the liner projection changes from point to point around the liner, turn the liner to a new position in the bore. If the liner projection is still not to specifications, move the liner to a different bore.5. When the cylinder projection is correct, put an alignment mark on the liner and block so the liner can be installed in the same position from which it was removed. Cylinder liner projection can be adjusted by the removal of material from (machining) the contact face of the cylinder block with the use of the 8S3140 Cylinder Block Counterboring Tool Arrangement. Machine to a minimum depth of 0.76 mm (.030 in) and to a maximum depth of 1.14 mm (.045 in). The instructions for the use of the tool group are in Special Instruction, Form No. FM055228. Shims are available for the adjustment of the liner projection. See topic, "Cylinder Liner Projection" in Testing & Adjusting Manual for the shim thickness and part number.6. Remove Tool (B) and (C). Remove the liner. 7. Put liquid soap on the bottom of the liner bore in the block, on the grooves in lower liner and on O-ring seals (4). Install the O-ring seals on the liner.8. Put filler band (5) in clean SAE 30 oil for a moment. Install it on the liner. Install the cylinder liner immediately in the cylinder block (before expansion of filler band). 9. Make sure the mark on the liner is in alignment with the mark on the block. Use Tool (A) to push the liner into position.10. Do Steps 5 through 9 for the remainder of the cylinder liners.End By:a. install pistons


Parts pin Mercury:

16175
 
16175 PIN, CLUTCH CAM
1004137, 1004201FB, 1004201JK, 1004201VB, 1B04201FB, 1F04201WB, 1F15211HM
16256 1
PIN
16256 1 PIN
1015203FL, 1015203YL, 1040203FL, 1040203YL, 1040213YL, 1B08201DB, 1F15211HM
95218 9
 
95218 9 PIN, Dowel
1015203FL, 1015203YL, 1025207FL, 1025207FM, 1025217FL, 1025217FM, 1030201FL, 1030201YL, 1030211FL, 1030271HL, 1030302FL, 1030312FL, 1030A01FL, 1030A11FL, 1031207ZF, 1040203FL, 1040203YL, 1040213YL, 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413K
815051001
 
815051001 PIN, Trim Lock
1B08201DB, 1F15211HM
851874002
 
851874002 PIN, Cylinder
1040203FL, 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ, 1B08201DB, 1F15211HM
851874003
 
851874003 PIN, Cylinder-Lower
1B08201DB, 1F15211HM
95218016
PIN, Spring
95218016 PIN, Spring
1025207FL, 1025207FM, 1025217FL, 1025217FM, 1030201FL, 1030211FL, 1030271HL, 1030302FL, 1030312FL, 1030A01FL, 1030A11FL, 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ, 1F25A17DM
898101378
 
898101378 PIN, To Swivel Bracket
1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ
Back to top