823553 Mercury PISTON ROD KIT (NUT TYPE)


823553 PISTON ROD KIT (NUT TYPE) Mercury 1135412MD, 1135412SD, 1135412VD, 1135473UD, 1150413SD, 1150413VD, 1175413MD, 1200473TD, 1200473UD, 1225412PD, 1225413RD PISTON
823553 PISTON ROD KIT (NUT TYPE) Mercury
Rating:
68

Buy PISTON ROD KIT (NUT TYPE) 823553 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 5
 

Mercury entire parts catalog list:

1135412MD 1992,1993,1994,1995
1135412SD 1996,1997,1998
1135412VD 1999
1135473UD 1998
1150413SD 1996,1997,1998
1150413VD 1999
1175413MD 1992,1993,1994,1995
1200473TD 1997
1200473UD 1998
1225412PD 1994,1995,1996,1997,1998
1225413RD 1995,1996,1997,1998

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
416-0292 Adapter 1
416-0288 Head 1 Start By:
Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Remove" for the correct procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Clean the bottom gasket surface of the cylinder head. Check the depth of the valves below the face of the cylinder head before the valve springs are removed. Refer to Specifications, "Cylinder Head Valves" for the correct dimensions.
Place a temporary identification mark on the heads of the valves in order to identify the correct position. Note: Inlet valves have a recess in the center of the head.
Use a suitable lifting device to position the cylinder head with the valve springs upward. The weight of the cylinder head is approximately 96 kg (212 lb). Note: Ensure that the cylinder head is kept on a clean, soft surface in order to prevent damage to the machined face.
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Illustration 1 g02727668
Install Tooling (A) into position on the cylinder head in order to compress appropriate valve spring (3).
Ensure that the valve spring is compressed squarely or damage to the valve stem may occur.
Apply sufficient pressure to Tooling (A) in order to remove valve keepers (1). Note: Do not compress the spring so that valve spring retainer (2) touches valve stem seal (4).
Slowly release the pressure on Tooling (A).
Illustration 2 g02727669
Place a temporary identification mark on valve spring (3) in order to identify the correct position.
Remove valve spring retainer (2). Remove valve spring (3).
Repeat Step 4 through Step 8 for the remaining valves.
Remove Tooling (A).
Remove valve stem seals (4). The inlet and exhaust valve stem seals are different, the valve stem seals are denoted by the color. Identify the position of the different color valve stem seals for installation purposes.
Use a suitable lifting device to turn over the cylinder head.
Place a temporary identification mark on valves (5). Remove valves (5) from the cylinder head. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
416-0292 Adapter 1
416-0288 Head 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The valves have a hard surface finish. Grinding compound must not be used on the valves. Grinding compound will damage the hard surface finish of the valves.
Clean all components of the cylinder head assembly. Ensure that all ports, all coolant passages, and, all lubrication passages in the cylinder head are free from debris. Follow Step 1.a through Step 1.e in order to inspect the components of the cylinder head assembly. Replace any components that are worn or damaged.
Inspect the cylinder head for wear and for damage. Refer to System Operation, Testing and Adjusting, "Cylinder Head Inspect" for the correct procedure.
Inspect the valve seats for wear and for damage. Refer to Specifications, "Cylinder Head Valves" for more information.
Inspect the valve guides for wear and for damage. Refer to Specifications, "Cylinder Head Valves" and System Operation, Testing and Adjusting, "Valve Guide - Inspect" for more information.
Inspect the valves for wear and for damage. Refer to Specifications, "Cylinder Head Valves" for more information.
Inspect the valve springs for damage and for the correct length. Refer to Specifications, "Cylinder Head Valves " for more information.
Illustration 3 g02727669
Lubricate the stems of valves (5) with clean engine oil. Install valves (5) in the appropriate positions in the cylinder head. Check the depth of the valves below the face of the cylinder head. Refer to System Operation, Testing and Adjusting, "Valve Depth - Inspect" for more information.
Use a suitable lifting device to turn over the cylinder head. The weight of the cylinder head is approximately 96 kg (212 lb). Note: Ensure that all of the valves remain in place.
Install new valve stem seals (4) onto each of the valve guides. The inlet and exhaust valve stem seals are different, the valve stem seals are denoted by the color. No


Parts piston Mercury:

85636A 4
 
85636A 4 PISTON RING
11354120D, 1135412GD, 1135412MD, 1135412SD, 1135412VD, 1135412WD, 1135726, 1150453JD, 1150625, 1150628, 1175626
815515A12
 
815515A12 PISTON RING (STANDARD)
11354120D, 1135412MD, 1150453JD, 1175413LD, 1175413MD
815268A 4
 
815268A 4 PISTON RING (.015 O.S.)
11354120D, 1135412MD, 1150453JD, 1175413LD, 1175413MD
7441A32
 
7441A32 PISTON (STARBOARD-STANDARD)
11354120D, 1135412MD, 1135412SD, 1135412VD, 1150453JD
7443A11
 
7443A11 PISTON (STARBOARD-.015 O.S.)
11354120D, 1135412MD, 1135412SD, 1135412VD, 1135412WD, 1150453JD
7445A11
 
7445A11 PISTON (STARBOARD-.030 OS.)
11354120D, 1135412MD, 1135412SD, 1135412VD, 1150453JD
834805A12
 
834805A12 PISTON RING
1200473TD, 1200473UD, 1200473VD
828222A 4
 
828222A 4 PISTON ASSEMBLY
1115473WD, 1135473UD, 1135473VD, 1200473UD, 1200473VD, 1200473WD, 1200473YD
Back to top