895172001 Mercury PLATE, Co-Pilot

Problem
In some applications, the fuel lines may fail on certain 3412 Generator Set, Industrial, and Marine Engines.
Affected Product
Model & Identification Number
Group 1
3412 (5AG101-173; 7HG1-87; 60M3255-4497; 38S13772-15290; 81Z6748-11441)
Group 2
3412 (60M4498-4750; 38S15291-15648; 81Z11442-12567)
Group 3
3412 (60M4751-4896; 38S15649-15853; 81Z12568-13134)
Group 4
3412 (5AG101-173; 7HG1-87; 60M3255-5087, 60M5089; 38S13772-16396; 81Z6748-14183)
Parts Needed
Group 1
1 - 7C6589 Clamp1 - 6I0349 Lines Group *1 - 6I0350 Lines Group *2 - 0L2070 Bolt4 - 9N3388 Screw5 - 0S1590 Bolt3 - 8T1296 Washer1 - 9Y3357 Clamp7 - 9X6458 Washer2 - 688438 Spacer*Lines Groups are used only for this portion of the Program. These lines groups contain the new 4P7801 through 4P7812 Fuel Lines. Engines covered by Rework Procedures '2' and '3' already have the new lines groups. After the completion of this Program, lines groups will not be available in the parts system.Additional parts needed for DIT (non-aftercooled) Engines
1 - 6I0348 Bracket Assembly5 - 0L1351 Bolt **2 - 0S1594 Bolt ****Use in place of the 0L2070 and 051590 Bolts.Group 2
2 - 7C6525 Clamp1 - 7C7747 Clamp1 - 6I4813 Clamp Kit *2 - 0L2070 Bolt5 - 9N3388 Screw1 - 4P7137 Bracket1 - 4P7144 Bracket3 - 0S1590 Bolt3 - 8T1296 Washer2 - 1W9167 Clamp Assembly1 - 1W9168 Clamp1 - 1W9169 Clamp5 - 9X6458 Washer2 - 688438 Spacer*Includes: 1 - 6D3848 Washer1 - 7M9831 Screw1 - 6I4812 Clamp2 - 6I4811 Damper1 - 6I4810 PlateAdditional parts needed for DIT (non-aftercooled) Engines
1 - 6I0348 Bracket Assembly5 - 0L1351 Bolt**2 - 0S1594 Bolt****Use in place of the 0L2070 and 0S1590 Bolts.Group 3
1 - 6I4813 Clamp Kit *1 - 0S1590 Bolt1 - 8T1296 Washer1 - 9X6458 Washer Includes: 1 - 6D3848 Washer1 - 7M9831 Screw1 - 6I4812 Clamp2 - 6I4811 Damper1 - 6I4810 PlateParts needed for DIT (non-aftercooled) Engines
1 - 0L1351 Bolt****Use in place of the 0S1590 BoltGroup 4
2 - 5P4939 Screw1 - 9Y3357 Clamp1 - 1029228 ClampAction Required
Parts Stock
Remove all 7C6301, 7C6302, 7C6303, 7C6304, 7C6305, 7C6306, 7C6307, 7C6308, 7C6309, 7C6310, 7C6311, and 7C6312 Fuel Lines from parts stock.
Affected Product
See the appropriate Rework Procedure.
Service Claim Allowances
Parts Stock
Submit one claim for all 7C6301, 7C6302, 7C6303, 7C6304, 7C6305, 7C6306, 7C6307, 7C6308, 7C6309, 7C6310, 7C6311, and 7C6312 Fuel Lines removed from parts stock.
Affected Product
Parts Disposition
Handle the parts in accordance with your Warranty Bulletin on warranty parts handling.
Attach.
(1 - Rework Procedure - Group 1)(2 - Rework Procedure - Group 2)(3 - Rework Procedure - Group 3)(4 - Rework Procedure - Group 4)Rework Procedure - Group 1
1. Clean and pre-paint the new 6I0349 and 6I0350 Fuel Line Groups in your shop before proceeding to the job site. If the engine to be reworked is non-aftercooled, also clean and pre-paint the new 6I0348 Bracket Assembly.
A. Tape off the number 3, 5, and 6 fuel lines in the area of the tower clamp. (See Illustration 1, Section C-C).
Illustration 1B. Make sure that the formed damper clamp for the number 4 and 6 fuel lines is close to the correct position and tape the fuel lines on each side of the damper clamp. (See Illustration 1, Section B-B).C Install 5F2807 Plastic Caps and 2F2990 Plastic Plugs on the ends of the fuel lines.D Clean and paint the fuel line groups. If applicable, clean and pre-paint the 6I0348 Bracker Assembly.E After drying completely, remove the tape. Do not remove the plastic caps and plugs until the fuel lines are ready to be installed on the engine.2. Remove all the mounting bolts from the fuel line brackets at the aftercooler housing on DITA Engines or at the 9Y1112 Bracket Assembly on DIT Engines. Except for the tower clamp assembly, new mounting bolts and washers will be used. Keep the 9X6458 Washers, they may be needed as spacers. The 9Y1112 Bracket Assembly is the large bracket on DIT (non-aftercooled) Engines used to support the fuel line brackets. This bracket is part of the 6N5140 Fastener Group.
If the vee brackets used between the left and right side lines groups on Caterpillar vehicular applications have been previously installed, remove them. Do not reuse these vee brackets. A new clamping arrangement is used on the new 6I0349 and 6I0350 Lines Groups on 3412 Generator Set Industrial, and Marine Engines.
3. Disassemble the tower clamp assembly behind the fuel injection pump. The 9Y3356 Clamp and 9Y3359 Clamp Assembly that form the tower clamp will be reused. (See Section C-C in Illustration 2).
Illustration 24. Disconnect all the fuel line nuts at the fuel injection pump and at the adapters in the valve cover bases.5. Remove the left side and right side fuel lines and clamps as separate assemblies.