42922 1 Mercury PLUG, Power Trim, Black, Gray


42922 1 PLUG, Power Trim, Black, Gray Mercury 10754120D, 1100312BD PLUG
42922 1 PLUG, Power Trim, Black, Gray Mercury
Rating:
98

Buy PLUG, Power Trim, Black, Gray 42922 1 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 4
 

Compatible models:

Mercury entire parts catalog list:

10754120D 1990,1991,1992,1993
1100312BD 1988,1989,1990,1991,1992,1993

Information:


When any servicing or repair of the engine cooling system is performed, the procedure must be performed with the engine on level ground. This procedure will allow you to accurately check the coolant level. This procedure will also help in avoiding the risk of introducing an air lock into the coolant system.
Drain
Pressurized System: Hot coolant can cause serious burns. To open the cooling system filler cap, stop the engine and wait until the cooling system components are cool. Loosen the cooling system pressure cap slowly in order to relieve the pressure.
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap.
Illustration 1 g02119093
Typical example
Open the drain cock or remove the drain plug (1) on the engine. Also remove the drain plug (2). Open the drain cock or remove the drain plug on the radiator. Note: Some applications have two drain plugs on the cooler, only one drain plug is required for draining.Allow the coolant to drain.
Dispose of used engine coolant properly or recycle. Various methods have been proposed to reclaim used coolant for reuse in engine cooling systems. The full distillation procedure is the only method acceptable by Caterpillar to reclaim the used coolant.
For information regarding the disposal and the recycling of used coolant, consult your Caterpillar dealer or consult Dealer Service Tools.Flush
Flush the cooling system with clean water in order to remove any debris.
Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to Torque Specifications, SENR3130 for more information on the correct torques.
Do not fill the cooling system faster than 5 L (1.3 US gal) per minute to avoid air locks.Cooling system air locks may result in engine damage.
Fill the cooling system with clean water. Install the cooling system filler cap.
Start and run the engine at low idle until the temperature reaches 49 to 66 °C (120 to 150 °F).
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap. Open the drain valve (if equipped) or remove the cooling system drain plugs. Allow the water to drain. Flush the cooling system with clean water. Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to Torque Specifications, SENR3130 for more information on the correct torques. Fill
Do not fill the cooling system faster than 5 L (1.3 US gal) per minute to avoid air locks.Cooling system air locks may result in engine damage.
Fill the cooling system with Extended Life Coolant (ELC). Refer to this Operation and Maintenance Manual, "Refill Capacities and Recommendations" topic (Maintenance Section) for more information on cooling system specifications. Do not install the cooling system filler cap.
Start and run the engine at low idle. Increase the engine rpm to high idle. Operate the engine in order to open the engine thermostat. This operation will allow any air in the system to be purged. Decrease the engine speed to low idle. Stop the engine.
Maintain the coolant level at the maximum mark that is correct for your application.
Clean the cooling system filler cap. Inspect the gasket that is on the cooling system filler cap. If the gasket that is on the cooling system filler cap is damaged, discard the old cooling system filler cap. Install a new cooling system filler cap. If the gasket that is on the cooling system filler cap is not damaged, use a 9S-8140 Pressurizing Pump in order to pressure test the cooling system filler cap. The correct pressure for the cooling system filler cap is stamped on the face of the cooling system filler cap. If the cooling system filler cap does not retain the correct pressure, install a new cooling system filler cap.
Start the engine. Inspect the cooling system for leaks and for proper operating temperature.


Parts plug Mercury:

45907
 
45907 PLUG, FLYWHEEL PULLER THREADS
10402139D, 1045217, 1050200, 1050312BC, 1060504, 1070312BC, 1070500, 1070717, 1075217DD, 1075217FD, 1075217PD, 1075217VD, 10752L7DF, 10752L7FF, 1075317DB, 1075317FB, 10754120D, 1075412DB, 1075412DD, 1075412DN, 1075412FB, 1075412FY, 1075524, 1075D73FY
67892
 
67892 PLUG, DRAIN (MAGNETIC)
1006206, 1008211RD, 1016207PD, 1016207RB, 1016207SB, 1018200, 1018204, 1025200, 1035204, 1035207, 1040200, 1040208, 1045217, 1050200, 1050312BC, 1050312LD, 1060504, 1070312BC, 1070500, 1070717, 10754120D, 1075524, 1080500, 1080508, 1090520, 1090524,
56800
 
56800 PLUG, PIPE - CYLINDER BLOCK
1004200, 1035207, 1040206, 10402139D, 1050302SD, 1050312BC, 1050312LD, 1055207UD, 1055207VB, 1070312BC, 10754120D, 1075524, 1090524, 1100312BD, 1115473WD, 1115525, 11354120D, 1135412GD, 1135412MD, 1135412SD, 1135412VD, 1135473UD, 1135473VD, 1135726,
99609A 1
 
99609A 1 PLUG ASSEMBLY
1035207, 1045217, 1050312BC, 1070312BC, 1070717, 10754120D, 1075524, 1090524, 1100312BD, 1115525, 11354120D, 1135412GD, 1135726, 1150453BD, 1150453GD, 1150453JD, 1150625, 1150628, 1175412GD, 1175413LD, 1175626, 1200412GD, 1200413GD, 1200628, 1220727
813435
PLUG KIT 
813435 PLUG KIT 
1035207, 10402139D, 1050302SD, 1050312BC, 1050312LD, 1075217PD, 10754120D, 1100312BD, 1100412PD
9596
 
9596 PLUG, MAIN JET
1050312LD, 1070312BC, 1070717, 10754120D, 1100312BD, 11354120D, 1135412MD, 1150453JD, 1225412PD
15864 1
 
15864 1 PLUG, Power Trim, Oyster
1070312BC, 1100312BD
811694
PLUG KIT (WME-20A&B/21A&B)
811694 PLUG KIT (WME-20A&B/21A&B)
1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040213YL, 1041312UB, 10432037D, 1043203DD, 1043203VD, 1043213DD, 1043302DD, 1043411DD, 1043412DB, 1043412DD, 1050302DB, 1050302FB, 1050302FD, 1050302SD, 1050312FB, 1050312LD, 1050411DD, 1050412D
Back to top