813458 PLUG KIT Mercury
1035207, 10402139D, 1050312BC, 1050312LD
PLUG
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
Total Power Parts 220-12303 Drive Assembly Compatible With/Replacement For Delco 1836541, 1844504, 1850844, 1858522, 1859631, 1859844, 1873877, 1873879, 1883879, 1887597, 1889923, 1901564
Total Power Parts Specs: Drive Assembly, Rotation Direction: Clockwise, ID: 0.630"/16 mm, Gear OD: 1.555"/39.500mm, Length: 3.866"/98.200 mm, Number Of Teeth: 10, Drive Type: Rubber Folo Thru, Wet Clutch Seal: False || Replaces OEM Numbers: 4049895, Arrowhead: SDR5023, SDR5042, 487922C1, 67033H, 74748H, 74751H, A25635, A7342, : 641179, 9B8959, 9B9133, Clark Equipment: 862748, 871528, 880592, 956003, Delco: 1836541, 1844504, 1850844, 1858522, 1859631, 1859844, 1873877, 1873879, 1883879, 1887597, 1889923, 1901564, 1901846, 1904245, 1905935, 1915515, 1920648, 1935534, 1939050, 1939325, 1946953, 1950844, 808898, 809505, 813458, 818305, 826155, Facet Drives: 480399, A1003, A-1003 || 1-year warranty protects you after your purchase. We're confident that our products will work flawlessly once installed in your vehicle. But in a rare case that it does not, we'll replace it anytime within one year of your order. If you have a problem, we will take every step to assist you, contact us for a replacement. || 100% New Aftermarket Drive Assembly built to meet OEM specifications
Total Power Parts Specs: Drive Assembly, Rotation Direction: Clockwise, ID: 0.630"/16 mm, Gear OD: 1.555"/39.500mm, Length: 3.866"/98.200 mm, Number Of Teeth: 10, Drive Type: Rubber Folo Thru, Wet Clutch Seal: False || Replaces OEM Numbers: 4049895, Arrowhead: SDR5023, SDR5042, 487922C1, 67033H, 74748H, 74751H, A25635, A7342, : 641179, 9B8959, 9B9133, Clark Equipment: 862748, 871528, 880592, 956003, Delco: 1836541, 1844504, 1850844, 1858522, 1859631, 1859844, 1873877, 1873879, 1883879, 1887597, 1889923, 1901564, 1901846, 1904245, 1905935, 1915515, 1920648, 1935534, 1939050, 1939325, 1946953, 1950844, 808898, 809505, 813458, 818305, 826155, Facet Drives: 480399, A1003, A-1003 || 1-year warranty protects you after your purchase. We're confident that our products will work flawlessly once installed in your vehicle. But in a rare case that it does not, we'll replace it anytime within one year of your order. If you have a problem, we will take every step to assist you, contact us for a replacement. || 100% New Aftermarket Drive Assembly built to meet OEM specifications
26-09-2017
Mitsubishi: Mitsubishi Materials
Mitsubishi Materials TNMG333MA MC5015 EDP # MIT 813458
EAP # MIT 813458
EAP # MIT 813458
Number on catalog scheme: 12
Mercury entire parts catalog list:
- MANUAL TILT COMPONENTS » 813458
1050312BC 1988,1989,1990
- MANUAL TILT COMPONENTS » 813458
- MANUAL TILT COMPONENTS » 813458
Information:
2. Remove two bolts (4) that fasten the fuel transfer pump to the governor drive housing. Remove the fuel transfer pump.3. Remove the O-ring seal from the transfer pump and remove the gasket from between the governor drive housing and transfer pump.Install Fuel Transfer Pump
1. Clean the contact surfaces of the transfer pump and the governor drive housing. 2. Install new gasket (1) between fuel transfer pump (2) and governor drive housing. Install an O-ring seal on the transfer pump and put the pump in position on the housing. Install the two bolts that fasten the pump to the housing. 3. Connect fuel pressure line (3) and fuel supply line (4) to the transfer pump.Disassemble Fuel Transfer Pump
START BY:a) remove fuel transfer pump 1. Remove bolts (1). Remove cover (2) from the fuel transfer pump. 2. Remove bolt (3). Remove gasket, spring and plunger from under bolt.3. Remove gear (4).4. Remove shaft assembly (5). 5. Remove O-ring seal (7) from body assembly.6. Install a 5/16"-18 NC forged eyebolt (6) in the plug. Remove plug (8) and O-ring seal. Remove the O-ring seal from the plug. 7. Remove valve assembly (9). 8. Remove two lip seals (10) from the body assembly. 9. Remove two bearings (11) from the body assembly with tooling (A).Assemble Fuel Transfer Pump
1. Install bearings in body (1) with tooling (A). Install bearing on gear end of body to a depth of 0.76 0.51 mm (.03 .02 in.) below the surface of the body. Install the bearing on the opposite end of the body even with the outside surface of the counterbore. 2. Put 8H5137 Permatex #2 Form-A-Gasket on the outside diameter of the two seals. Use tooling (A) and install the first seal with the lip of the seal toward the bearings and 10.31 0.25 mm (.406 .10 in.) below the outside surface of the body assembly. Use tooling (A) and install the second seal with the lip of the seal away from the bearings and even with the outside surface of the body assembly. Put a small amount of clean fuel on the lip of the seals. 3. Install the valve assembly in the body assembly with tooling (A) to a depth of 14.5 0.5 mm (.57 .02 in.). 4. Install O-ring seal (3) on the plug. Install a 5/16"-18 NC forged eyebolt (2) in the plug. Put a small amount of clean diesel fuel on the O-ring seal and install plug (4) in the body assembly. Make sure plug is even with the surface of the body. 5. Install O-ring seal on the body assembly.6. Put a small amount of clean diesel fuel on the lip seals. Put tool (B) in position on shaft assembly. Install shaft assembly (5) in the body assembly. 7. Install gear (7).
Do not allow the sealant to enter into the pump.
8. Put 8H5137 Permatex #2 Form-A-Gasket on the body assembly surface that makes contact with the cover. Install cover (6).9. Shaft assembly must turn by hand after cover is installed. 10. Install plunger (8), spring (9), gasket (11) and plug (10) in body assembly. Tighten plug to a torque of 37 4 N m (27 3 lb.ft.).END BY:a) install fuel transfer pump
1. Clean the contact surfaces of the transfer pump and the governor drive housing. 2. Install new gasket (1) between fuel transfer pump (2) and governor drive housing. Install an O-ring seal on the transfer pump and put the pump in position on the housing. Install the two bolts that fasten the pump to the housing. 3. Connect fuel pressure line (3) and fuel supply line (4) to the transfer pump.Disassemble Fuel Transfer Pump
START BY:a) remove fuel transfer pump 1. Remove bolts (1). Remove cover (2) from the fuel transfer pump. 2. Remove bolt (3). Remove gasket, spring and plunger from under bolt.3. Remove gear (4).4. Remove shaft assembly (5). 5. Remove O-ring seal (7) from body assembly.6. Install a 5/16"-18 NC forged eyebolt (6) in the plug. Remove plug (8) and O-ring seal. Remove the O-ring seal from the plug. 7. Remove valve assembly (9). 8. Remove two lip seals (10) from the body assembly. 9. Remove two bearings (11) from the body assembly with tooling (A).Assemble Fuel Transfer Pump
1. Install bearings in body (1) with tooling (A). Install bearing on gear end of body to a depth of 0.76 0.51 mm (.03 .02 in.) below the surface of the body. Install the bearing on the opposite end of the body even with the outside surface of the counterbore. 2. Put 8H5137 Permatex #2 Form-A-Gasket on the outside diameter of the two seals. Use tooling (A) and install the first seal with the lip of the seal toward the bearings and 10.31 0.25 mm (.406 .10 in.) below the outside surface of the body assembly. Use tooling (A) and install the second seal with the lip of the seal away from the bearings and even with the outside surface of the body assembly. Put a small amount of clean fuel on the lip of the seals. 3. Install the valve assembly in the body assembly with tooling (A) to a depth of 14.5 0.5 mm (.57 .02 in.). 4. Install O-ring seal (3) on the plug. Install a 5/16"-18 NC forged eyebolt (2) in the plug. Put a small amount of clean diesel fuel on the O-ring seal and install plug (4) in the body assembly. Make sure plug is even with the surface of the body. 5. Install O-ring seal on the body assembly.6. Put a small amount of clean diesel fuel on the lip seals. Put tool (B) in position on shaft assembly. Install shaft assembly (5) in the body assembly. 7. Install gear (7).
Do not allow the sealant to enter into the pump.
8. Put 8H5137 Permatex #2 Form-A-Gasket on the body assembly surface that makes contact with the cover. Install cover (6).9. Shaft assembly must turn by hand after cover is installed. 10. Install plunger (8), spring (9), gasket (11) and plug (10) in body assembly. Tighten plug to a torque of 37 4 N m (27 3 lb.ft.).END BY:a) install fuel transfer pump
Parts plug Mercury:
64649
64649 PLUG, PLASTIC - TRIM TAB SCREW HOLE
1035204, 1035207, 1040200, 1040208, 10402139D, 1045217, 1050200, 1050312BC, 1060504, 1070500, 1075524, 1080500, 1080508, 1090520, 1090524, 1090528, 111047JHD, 1115473WD, 1115503, 1115520, 1115523, 1115525, 1115528, 11354120D, 1135412GD, 1135412MD, 11
56800
56800 PLUG, PIPE - CYLINDER BLOCK
1004200, 1035207, 1040206, 10402139D, 1050302SD, 1050312BC, 1050312LD, 1055207UD, 1055207VB, 1070312BC, 10754120D, 1075524, 1090524, 1100312BD, 1115473WD, 1115525, 11354120D, 1135412GD, 1135412MD, 1135412SD, 1135412VD, 1135473UD, 1135473VD, 1135726,
89219
89219 PLUG
1050302SD, 1050312LD, 11354120D, 1135412GD, 1135412MD, 1135412SD, 1135726, 1135D73CD, 1150413SD, 1150453BD, 1150453GD, 1150453JD, 1150625, 1150628, 1175412GD, 1175413LD, 1175413MD, 1175626, 1200412GD, 1200413GD, 1200453CD, 1200628, 1200D73AD, 1200D73
88618
94879 1
813435
813435 PLUG KIT
1035207, 10402139D, 1050302SD, 1050312BC, 1050312LD, 1075217PD, 10754120D, 1100312BD, 1100412PD
811694
811694 PLUG KIT (WME-20A&B/21A&B)
1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040213YL, 1041312UB, 10432037D, 1043203DD, 1043203VD, 1043213DD, 1043302DD, 1043411DD, 1043412DB, 1043412DD, 1050302DB, 1050302FB, 1050302FD, 1050302SD, 1050312FB, 1050312LD, 1050411DD, 1050412D
816031
