826193T03 Mercury PROPELLER SHAFT


826193T03 PROPELLER SHAFT Mercury 1A40302HZ, 1A40303KZ, 1A40311HZ, 1A40403HZ, 1A40412HZ, 1A41452EZ, 1A51411HZ, 1A51412HZ, 1A51452EZ, 1A60351EZ, 1A60412HZ, 1A60452EZ, 1A60452HZ, 1A60463EZ, 1A6C411KZ, 1A6C413KZ, 1E41412HB, 1E41452HB, 1E51412HB, 1E51412HZ, 1E60403HZ, 1E60412HZ, 1E60413K PROPELLER
826193T03 PROPELLER SHAFT Mercury
Rating:
43

Buy PROPELLER SHAFT 826193T03 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 14
 

Mercury entire parts catalog list:

1A40302HZ 2006,2010
1A40303KZ 2010
1A40311HZ 2006
1A40403HZ 2006,2010
1A40412HZ 2006
1A41452EZ 2006
1A51411HZ 2006
1A51412HZ 2006
1A51452EZ 2006
1A60351EZ 2007
1A60412HZ 2006
1A60452EZ 2006
1A60452HZ 2006
1A60463EZ 2007
1A6C411KZ 2009
1A6C413KZ 2009
1E41412HB 2006
1E41452HB 2006
1E51412HB 2006
1E51412HZ 2006
1E60403HZ 2006
1E60412HZ 2006
1E60413KZ 2009
1E60452HB 2006
1F40203HZ 2006

Information:


Illustration 1 g03882525
Typical MEUI A injector
(1) Solenoid prongs
(2) Top of injector
(3) Height adjustment tool ledgeMechanical Electronic Unit Injectors (MEUI) A have the typical features that are shown in Illustration 1. The injectors typically have solenoid prongs (1), a flat top to the injector (2), and a ledge for the height adjustment tool (3).MEUI A Injector Adjustment
Table 1
Required Tools
Part Number Part Name Quantity
9U-7227 Injector Height Gauge 1
Illustration 2 g01332476
Injector Mechanism (Typical example)
(1) Rocker arm
(2) Adjusting screw
(3) Locknut
(4) 9U-7227 Injector Height GaugeTo adjust the unit injectors on cylinders 3, 5, and 6 use the following procedure:
Put the No. 1 piston at the top center position on the compression stroke. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston".
Injector height gauge (4) is used to obtain a dimension of 78.0 0.2 mm (3.07 0.01 inch). The dimension is measured from the top of the unit injector to the machined ledge of the fuel injector body.
Set the injector height tool body on top of the injector tappet body. The rod of the height adjustment tool should sit on the machined ledge of the injector body.
Turn unit injector adjusting screw (2) clockwise until the correct height is obtained.Note: The top of the injector height tool rod has two steps on it. The middle of the steps should be flush with the injector height tool body.
Hold the adjusting screw in this position and tighten locknut (3) to a torque of 100 10 N m (74 7 lb ft).
To adjust the unit injectors on cylinders 1, 2, and 4, remove the timing bolt. Turn the flywheel by 360 degrees in the direction of engine rotation. The direction of engine rotation is counterclockwise, as the engine is viewed from the flywheel end. This will put the number 1 piston at the top center position on the exhaust stroke.
Repeat Steps 3 through 4.
Remove the timing bolt from the flywheel after all the unit injector adjustments have been made. Reinstall the valve mechanism cover.MEUI C Injector Overview
Illustration 3 g03882544
Typical MEUI C injector
(1) Tappet
(2) Electrical connectorMechanical Electronic Unit Injectors (MEUI) C have the typical features that are shown in Illustration 3. The injectors typically have a raised tappet (1), and electrical connector (2).MEUI C Injector Adjustment
Set the engine to Top Dead Center (TDC) for number 1 piston. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston".
Set injectors 3, 5, and 6 using the procedure that follows.
Turn the adjustment screw clockwise for the injector rocker mechanism until it touches the top of the injector.
Turn the adjustment screw an additional 180 degrees clockwise.
Hold the adjustment screw and torque the nut to 55 10 N m (41 7 lb ft).
To adjust injectors 1, 2, and 4 rotate the engine 360 degrees and pin the flywheel.
Turn the adjustment screw clockwise for the injector rocker mechanism until it touches the top of the injector.
Turn the adjustment screw an additional 180 degrees clockwise.
Hold the adjustment screw and torque the nut to 55 10 N m (41 7 lb ft).


Parts propeller Mercury:

14493
 
14493 PROPELLER SHAFT
1050302SD, 1050312LD, 1055207DB, 1055207UD, 1055207VB, 1A40302FD, 1A40311FZ, 1A41412ZB, 1A41452EZ, 1A41452FU, 1A51411HZ, 1A51412HZ, 1A51452EZ, 1A60412HZ, 1A60452EZ, 1A60452HZ, 1E60452HB, 1F40203FD, 1F40213FZ, 1F40452YB, 1F41452YD, 1F51452YB
850308
PROPELLER SHAFT
850308 PROPELLER SHAFT
1050302SD, 1055207DB, 1055207UD, 1055207VB, 1075217DD, 1075217FD, 1075217PD, 1075217VD, 10752L7DF, 10752L7FF, 1075317DB, 1075317FB, 1075412DB, 1075412DD, 1075412DN, 1075412FB, 1075412FY, 1075D73FY, 1075D73HY, 1090412DB, 1090412DC, 1090412DD, 1090412D
888804
 
888804 PROPELLER SHAFT
1115F13CC, 1115F13FF, 1A41452EZ, 1A41452FU, 1A51411HZ, 1A51412HZ, 1A51452EZ, 1A60351EZ, 1A60412HZ, 1A60452EZ, 1A60452HZ, 1A60463EZ, 1A6C411KZ, 1A6C413KZ, 1B75412CF, 1B75413DF, 1E41412HB, 1E41452HB, 1E51412HB, 1E51412HZ, 1E60403HZ, 1E60412HZ, 1E60413K
Back to top