62351A 2 Mercury RECTIFIER ASSEMBLY


62351A 2 RECTIFIER ASSEMBLY Mercury 1007208, 1007209, 1010208, 1018200, 1018204, 1020208, 1025200, 1075204, 1110204, 1200203, 1300623, 1402202, 1402205 RECTIFIER
62351A 2 RECTIFIER ASSEMBLY Mercury
Rating:
33

Buy RECTIFIER ASSEMBLY 62351A 2 Mercury genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$19.99

14-12-2024

US: Areyourshop
Areyourshop Rectifier Fit for Mercury Outboard Replace # 62351A1 62351A2 816770T 8M0058226
Areyourshop ★Please check the description or use the year/make/model check finder and replace part numbers to confirm the compatibility before purchasing. || ★REFERENCE PART NUMBER(S):62351A1,62351A2,816770,816770T,8M0058226 || ★ Features:✔Direct replacement to your original unit.✔Plug-and-play, direct fit, easy installation.✔No assembly required.Higher grade of electric components.✔Improved heat sink and charging capabilities.✔The quality exceeds or meet the OEM equipment.✔All products shipped are tested. || ★NOTICE:Before installing your new voltage regulator rectifier;Check the AC output of the stator. Replace any burned or corroded connectors on stator and regulator/rectifier Check and repair any melted wiring. Use hi-temp dielectric grease on all connectors. || ★Provides the performance and dependability you expect from Areyourshop
$25.99

24-11-2024
0.6613[0.30] Pounds
CN: Outboard Motor Parts
TUO ZHOU 62351A1 Marine Boat Voltage Regulator Rectifier for Mercury Outboard Motors 62351A1 62351A2 816770, As shown in the picture
TUO ZHOU 62351A1
$15.88

20-01-2025

CN: KUNOANZ-US
332-62351A1 Voltage Regulator Rectifier for Mercury 6 7.5 8 9.8 9.9 10 15 18 20 25 30 35 40 45 50 55 60 70 75 80 90 100 115 135 150 175 200 220 HP 2.5 L 2/3/4/6-Cyl Outboard 154-6770 Sierra 18-5707
KUNOANZ [Accurate search] :Mercury outboard engine query parts are rather special!!!! Only by following the engine's [HP] + [Model No.] + [Serial No.] and other data can you accurately look up the parts that your engine fits.The year is not accurate. || [Tips] : We will show more detailed information about the product on the details page below to ensure that we can help you to buy the correct replacement part || [Note] : In order to prevent purchasing the wrong unsuitable part, which could result in wasted time, you need to determine suitability by using the information on the engine nameplate || [Adaptation] : Part of the Mercury Mariner(6hp 7.5hp 8hp 9.8hp 9.9hp 10hp 15hp 18hp 20hp 25hp 30hp 35hp 40hp 45hp 50hp 55hp 60hp 70hp 75hp 80hp 90hp 100hp 115hp 135hp 150hp 175hp 200hp 220hp) , 2/3/4/6-Cylinder Engine || [OEM#] : Replacing part numbers For Mercury : 332-2910A1 , 332-2910A2 , 332-2910A3 , 62351A1 , 62351A2 , 78614A1 , 816770 , 816770T , 8M0058226 ; Cross Reference OEM#: 62351A6 , 62351A8 , 62351A9 ,62351A10 ,CDI Electronics : 154-6770 ;Sierra : 18-5707 ;ARCO : AR351 ;OBR Red Rhino : ME-160 ;Mallory : 9-17100 ;GLM : 72310
Number on catalog scheme: 17
 

Mercury entire parts catalog list:

1007208 1978
1007209 1979,1980,1981,1982,1983,1984,1985
1010208 1978
1018200 1980,1982,1983
1018204 1984,1985,1986,1987
1020208 1978,1979,1980
1025200 1980,1982,1983
1075204 1974,1975,1976,1977
1110204 1974,1975,1976,1977
1200203 1973,1974,1975,1976,1977
1300623 1983,1984,1985,1986,1987
1402202 1972,1973,1974
1402205 1975,1976,1977

Information:


Illustration 1 g00761072
SchematicTest Step 1. Inspect Electrical Connectors and Wiring
Turn the keyswitch to the OFF/RESET position.
Thoroughly inspect the J1/P1 ECM connector, the J3/P3 machine connector, and all other connectors in the wiring harness. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector and the sensor connectors that are associated with the active diagnostic code.
Check the ECM connector (allen head screw) for the proper torque of 6.0 N m (55 lb in).
Inspect the following components for damage, corrosion, and incorrect attachment:
Battery posts
Alternator
Breaker
Engine ground
Chassis groundExpected Result:All connectors, pins, and sockets are inserted and coupled. The harness and wiring are free of corrosion, of abrasion, and of pinch points. All connections and grounds are tight and free of corrosion.Results:
OK - The harness and wiring are OK. Proceed to Test Step 2.
Not OK - There is a problem with the harness and/or wiring.Repair: Repair the circuit.Verify that the repair eliminates the problem.STOPTest Step 2. Check the Starting Aid Switch Status on the Electronic Service Tool
Remove the ether canister from the ether solenoid.
Connect Caterpillar Electronic Technician (ET) to the service tool connector.
Turn the keyswitch to the ON position.
Press the starting aid switch to "MANUAL". Observe the "Starting Aid Switch Status" on Cat ET.Expected Result:When the starting aid switch is pressed, Cat ET should display the status of the starting aid switch as ON.When the starting aid switch is not pressed, Cat ET should display the status of the starting aid switch as OFF.Results:
OK - Cat ET displayed the expected results. The starting aid switch is operating correctly. Proceed to Test Step 6.
Not OK - Cat ET did not display the expected results. The ECM is not properly reading the signal from the starting aid switch. Proceed to Test Step 3.Test Step 3. Check the Resistance of the Relay
Illustration 2 g00761074
Connector for the ether relay
Turn the keyswitch to the OFF/RESET position.
Disconnect the wires at terminal 86 (Ether ON) and terminal 85 (Solenoid Return) at the ether relay.
Measure the resistance across terminal 86 (Ether ON) and terminal 85 (Solenoid Return).
Reconnect the wires to the ether relay.Expected Result:The resistance is between 250 Ohms and 500 Ohms.Results:
OK - The resistance is acceptable. Proceed to Test Step 4.
Not OK - The resistance is not acceptable. The relay is faulty.Repair: Replace the relay.Verify that the repair eliminates the problem.STOPTest Step 4. Short the Switch Wires
Remove wire F721-GY (Starting Aid Switch) and wire 998-BR (Digital Return) from the starting aid switch.
Short wire F721-GY (Starting Aid Switch) to wire 998-BR (Digital Return).Expected Result:When the wires are shorted, Cat ET displays the status of the starting aid switch as ON.When the wires are not shorted, Cat ET displays the status of the starting aid switch as OFF.Results:
OK - Cat ET displayed the expected results. The starting aid switch is not operating correctly.Repair: Replace the starting aid switch.Verify that the repair eliminates the problem.STOP
Not OK - Cat ET did not display the expected results. Proceed to Test Step 5.Test Step 5. Short the Switch Inputs at the ECM
Illustration 3 g00936533
J1/P1 breakout
Turn the keyswitch to the OFF/RESET position and install a 7X-1715 Adapter Cable (40 Pin Breakout T) at the J1/P1 ECM connector.
Turn the keyswitch to the ON position.
Use a suitable piece of wire to short P1:19 (Starting Aid Switch) and P1:29 (Digital Return) at the breakout.
Observe the results on the "Status" screen on Cat ET.Expected Result:When the wires are shorted, Cat ET displays the status of the starting aid switch as ON.When the wires are not shorted, Cat ET displays the status of the starting aid switch as OFF.Results:
OK - Cat ET displayed the expected results. There is a problem in the wiring between the switch and the ECM.Repair: Repair the circuit.Verify that the repair eliminates the problem.STOP
Not OK - Cat ET did not display the expected results. The ECM is not reading the switch input properly.Repair: Verify your results. Replace the ECM. Refer to Troubleshooting, "Replacing the ECM" before replacing the ECM.Verify that the repair eliminates the problem.STOPTest Step 6. Check the Resistance of the Ether Solenoid
Turn the keyswitch to the OFF/RESET position.
Disconnect the J37/P37 ether solenoid connector.
Measure the resistance between J37:1 (Solenoid Power) and J37:2 (Solenoid Return).Expected Result:The resistance is less than ten Ohms.Results:
OK - Resistance is less than ten Ohms. Proceed to Test Step 7.
Not OK - Resistance is more than ten Ohms. The ether solenoid is faulty.Repair: Replace the ether solenoid.Verify that the repair eliminates the problem.STOPTest Step 7. Check the Supply Voltage to the Ether SolenoidNote: The ether canister must be removed prior to activating this test.
Turn the keyswitch to the ON position.
Proceed to the "Diagnostic Override Screen" on C


Parts rectifier Mercury:

62351A 1
RECTIFIER ASSEMBLY
62351A 1 RECTIFIER ASSEMBLY
1035204, 1040200, 1040208, 1045217, 1050200, 1050312BC, 1060504, 1070312BC, 1070500, 1070717, 1075524, 1080500, 1080508, 1090520, 1090524, 1090528, 1115503, 1115520, 1115523, 1115525, 1115528, 1135726, 1140520, 1140528, 1140629, 1150453BD, 1150503, 1
Back to top