43018A 1 Mercury REED SET (75/80/90)


43018A 1 REED SET (75/80/90) Mercury 1070312BC, 1070717, 1075217DD, 1075217FD, 1075217PD, 1075217VD, 10752L7DF, 10752L7FF, 1075317DB, 1075317FB, 10754120D, 1075412DB, 1075412DD, 1075412DN, 1075412FB, 1075412FY, 1090412DB, 1090412DC, 1090412DD, 1090412DN, 1090412DY, 1090412FF, 1090412FY, REED
43018A 1 REED SET (75/80/90) Mercury
Rating:
33

Buy REED SET (75/80/90) 43018A 1 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 36
 

Mercury entire parts catalog list:

1070312BC 1988,1989,1990
1070717 1987
1075217DD 2005
1075217FD 2006
1075217PD 1994,1995,1996,1997,1998
1075217VD 1999,2000,2001,2002,2003,2004
10752L7DF 2005
10752L7FF 2006
1075317DB 2005
1075317FB 2006
10754120D 1990,1991,1992,1993
1075412DB 2005
1075412DD 2005
1075412DN 2005
1075412FB 2006
1075412FY 2006
1090412DB 2005,2006
1090412DC 2005
1090412DD 2005
1090412DN 2005
1090412DY 2005,2006
1090412FF 2010
1090412FY 2006
1090422DY 2005
1090422FF 2010
1090472DD 2005
1090472FF 2010
1090472FY 2006
1100312BD 1988,1989,1990,1991,1992,1993
1100412PD 1994,1995,1996,1997,1998
1100412VB 1999,2000,2001,2002,2003,2004
1115412DB 2005,2006

Information:


To prevent damage to the intake and exhaust valves, an adjustment must be made to the valve clearance setting. Loosen the nuts on each rocker arm and move the adjustment screw on each rocker arm away from the bridge as far as possible.
1. Put engine in position on Tool (A) and turn the engine over on its side. Make sure the blocks that are used as support for the top of the engine are against the cylinder head only and not against the exhaust manifold or valve cover bases. 2. Loosen the nuts that hold each connecting rod bearing caps (1) in position. Turn the crankshaft if necessary to loosen all the nuts. Make sure the nuts are still tight enough to hold the bearing caps in place when the crankshaft is turned. 3. Turn the crankshaft so that "V" on the crankshaft gear is in alignment with "V" mark (3) on the idler gear.4. Remove the bearing caps that hold the connecting rods in position against the crankshaft. 5. Remove bearings (4) from each bearing cap. Make sure that each bearing is kept with the bearing cap it is removed from for correct installation purposes. 6. Remove


Parts reed Mercury:

42963A 4
42963A 5
43018A 2
 
43018A 2 REED SET (70)
1070312BC, 1070717
42963A11
REED BLOCK ASSEMBLY
42963A11 REED BLOCK ASSEMBLY
1075217DD, 1075217FD, 1075217PD, 1075217VD, 10752L7DF, 10752L7FF, 1075317DB, 1075317FB, 10754120D, 1075412DB, 1075412DD, 1075412DN, 1075412FB, 1075412FY, 1090412DB, 1090412DC, 1090412DD, 1090412DN, 1090412DY, 1090412FF, 1090412FY, 1090422DY, 1090422F
Back to top