898101T76 REGULATOR, Fuel Mercury
1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ
REGULATOR
Price: query
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$86.11
02-07-2023
0.1256[0.06] Pounds
-: -
MERCURY Regulator mfg Part Number 898101T76
Number on catalog scheme: 3
Mercury entire parts catalog list:
- FUEL RAIL AND VAPOR SEPARATOR COMPONENTS » 898101T76
- FUEL RAIL AND VAPOR SEPARATOR COMPONENTS » 898101T76
- FUEL RAIL AND VAPOR SEPARATOR COMPONENTS » 898101T76
- FUEL RAIL AND VAPOR SEPARATOR COMPONENTS » 898101T76
- FUEL RAIL AND VAPOR SEPARATOR COMPONENTS » 898101T76
Information:
3. Remove guard assembly (3).4. Loosen clamps (2). Slide hose (1) away from the water pump. 5. Loosen clamps on hose (4). Slide the hose off of the water pump elbow.6. Remove bolts (5) that hold water pump (6) to the timing gear cover and the cylinder head. Remove the water pump.Install Water Pump
1. Make sure the O-ring seal and the gasket are in position on the water pump. 2. Install water pump (1) on the timing gear cover. 3. Install two bolts (3) that hold the water pump elbow to the cylinder head.4. Put hose (4) in position on the water pump elbow. Install the clamps that hold it in position.5. Put the hose in position on the bottom of the water pump. Install the clamps that hold it in position.6. Install guard assembly (2).7. Install the engine side guard assembly (not shown).8. Fill the engine cooling system to the correct level. See the LUBRICATION AND MAINTENANCE GUIDE.Disassemble Water Pump
start by:a) remove water pump 1. Remove cover (1) from water pump (2). 2. Loosen bolt (3) .25 in. (6.35 mm). Hit the bolt with a soft hammer to remove impeller (4) from the shaft. 3. Remove spring and seal assembly (5) from the shaft (6). 4. Turn the housing over and remove bolt and washer (7). Remove bearing (8) and gear (9) as a unit. 5. Use tool (A) and a press to remove bearing (8) from gear (9). 6. Remove snap ring (10) with tool (B). 7. Remove bearing (11) and shaft (6) as a unit. 8. Use tool (A) and a press to remove bearing (11) from the shaft. 9. Remove the ceramic ring and seal (12) from the housing. 10. Remove the lip seal (13) from the housing with tool (C).Assemble Water Pump
1. Install lip seal in water pump housing with tooling (A). The lip of the seal must be toward the bearings. Put clean SAE 30 engine oil on the lip of the seal. 2. Use a press to install shaft (1) in bearing (2). 3. Install the shaft (1) and bearing in the housing (3). 4. Install snap ring (4) in housing with tool (B). 5. Heat the bearing (5) in oil to a maximum temperature of 275°F (135°C) and install on gear (6). 6. Put gear (6) and bearing in position on shaft and install bolt and washer.
Clean water only is permitted for use as a lubricant for assistance at installation. Do not damage or put hands on the wear surface of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
7. Put the ceramic ring (7) in position in the rubber seal. Use hand pressure and the tool (which is with the replacement ring) to install the ceramic ring. 8. Remove spring from the seal assembly (8). Use hand pressure and the tool (which is with the replacement ring) to install the seal assembly. Press seal assembly on shaft until seal faces make light contact. 9. Install spring (9). Put impeller (10) in position and install washer and bolt. Tighten bolt to a torque of 27 1 lb.ft. (38 1 N m).10. Install gasket and cover on the housing.end by:a) install water pump
1. Make sure the O-ring seal and the gasket are in position on the water pump. 2. Install water pump (1) on the timing gear cover. 3. Install two bolts (3) that hold the water pump elbow to the cylinder head.4. Put hose (4) in position on the water pump elbow. Install the clamps that hold it in position.5. Put the hose in position on the bottom of the water pump. Install the clamps that hold it in position.6. Install guard assembly (2).7. Install the engine side guard assembly (not shown).8. Fill the engine cooling system to the correct level. See the LUBRICATION AND MAINTENANCE GUIDE.Disassemble Water Pump
start by:a) remove water pump 1. Remove cover (1) from water pump (2). 2. Loosen bolt (3) .25 in. (6.35 mm). Hit the bolt with a soft hammer to remove impeller (4) from the shaft. 3. Remove spring and seal assembly (5) from the shaft (6). 4. Turn the housing over and remove bolt and washer (7). Remove bearing (8) and gear (9) as a unit. 5. Use tool (A) and a press to remove bearing (8) from gear (9). 6. Remove snap ring (10) with tool (B). 7. Remove bearing (11) and shaft (6) as a unit. 8. Use tool (A) and a press to remove bearing (11) from the shaft. 9. Remove the ceramic ring and seal (12) from the housing. 10. Remove the lip seal (13) from the housing with tool (C).Assemble Water Pump
1. Install lip seal in water pump housing with tooling (A). The lip of the seal must be toward the bearings. Put clean SAE 30 engine oil on the lip of the seal. 2. Use a press to install shaft (1) in bearing (2). 3. Install the shaft (1) and bearing in the housing (3). 4. Install snap ring (4) in housing with tool (B). 5. Heat the bearing (5) in oil to a maximum temperature of 275°F (135°C) and install on gear (6). 6. Put gear (6) and bearing in position on shaft and install bolt and washer.
Clean water only is permitted for use as a lubricant for assistance at installation. Do not damage or put hands on the wear surface of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
7. Put the ceramic ring (7) in position in the rubber seal. Use hand pressure and the tool (which is with the replacement ring) to install the ceramic ring. 8. Remove spring from the seal assembly (8). Use hand pressure and the tool (which is with the replacement ring) to install the seal assembly. Press seal assembly on shaft until seal faces make light contact. 9. Install spring (9). Put impeller (10) in position and install washer and bolt. Tighten bolt to a torque of 27 1 lb.ft. (38 1 N m).10. Install gasket and cover on the housing.end by:a) install water pump