803748Q01 REPAIR KIT, Water Impeller Mercury
1B08201DB
REPAIR
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
Water Pump Impeller Repair Kit 3B2-87322-2 for Nissan Tohatsu 3B2873222M Outboard for Mercury 46-803750A03 803748K01 803748Q01 9.9 15 18 20 HP 2 & 4 Strok M8B M9.8B NS8B NS9.8B
JAETHB Replacing part numbers:For Mercury 46-803750A03,80375A03,803748Q01,803748K01;Nissan Tohatsu 3B2873222M,3B2-87322-2 || Adaptation:For Mercury 9.9HP 15HP 18HP 20HP 2/4-Stroke 2002-2023 M8B M9.8B NS8B NS9.8B || Package Contains:Water Pump Impeller,Pin Roll, Driveshaft,Cup liner stainless steel,Wear plate stainless steel,Gasket,Boat and washer || Quality:Original level of quality and durability, the impellers are manufactured from high quality rubber and will not be damaged even after long periods of immersion in salt water || Service:Please make sure the model number, part number and picture are consistent with your product before ordering Please contact me if you have any installation problems or product issues
JAETHB Replacing part numbers:For Mercury 46-803750A03,80375A03,803748Q01,803748K01;Nissan Tohatsu 3B2873222M,3B2-87322-2 || Adaptation:For Mercury 9.9HP 15HP 18HP 20HP 2/4-Stroke 2002-2023 M8B M9.8B NS8B NS9.8B || Package Contains:Water Pump Impeller,Pin Roll, Driveshaft,Cup liner stainless steel,Wear plate stainless steel,Gasket,Boat and washer || Quality:Original level of quality and durability, the impellers are manufactured from high quality rubber and will not be damaged even after long periods of immersion in salt water || Service:Please make sure the model number, part number and picture are consistent with your product before ordering Please contact me if you have any installation problems or product issues
$28.99
22-10-2023
-: -
Boat Engine 3B2873220/1 3B2-87322-2 3B2873222M Water Pump Repair Kit for Nissan Tohatsu Outboard Motor 8HP 9.8HP M8B M9.8B NS8B NS9.8B/46-803750A03 803748K01 803748Q01 for Mercury, fit Sierra 18-48317
Engine Position: Outboard Engine 9.9HP 15HP 18HP 20HP 2/4-Stroke (without Housing) || Replaces Part Number: 3B2873220 3B2873221 3B2-87322-0 3B2-87322-1 3B2873220M 3B2873221M 3B2-87322-2 3B2873222 3B2873222M 18-48317 46-803750A03 803748K01 803748Q01 || PACKAGE INCLUDED: 1X Water pump impeller 1X Pin Roll, Driveshaft 1X Cup liner stainless steel 1X Wear plate stainless steel 3X Gasket 4X Boat and washer || NOTE: If you are unsure, please provide your engine serial number.
Engine Position: Outboard Engine 9.9HP 15HP 18HP 20HP 2/4-Stroke (without Housing) || Replaces Part Number: 3B2873220 3B2873221 3B2-87322-0 3B2-87322-1 3B2873220M 3B2873221M 3B2-87322-2 3B2873222 3B2873222M 18-48317 46-803750A03 803748K01 803748Q01 || PACKAGE INCLUDED: 1X Water pump impeller 1X Pin Roll, Driveshaft 1X Cup liner stainless steel 1X Wear plate stainless steel 3X Gasket 4X Boat and washer || NOTE: If you are unsure, please provide your engine serial number.
RUIJADE 3B2-87322-2 OutboardaRUIJADE 3B2-87322-2 Compatible with Tohatsu Water Pump Repair Kit 3B2873222M, for Tohatsu Outboard 8HP 9.8HP M8B M9 Water Pump Impeller Repair Kit Compatible with Tohatsu
RUIJADE 😀【3B2-87322-2】 This is Top Quality Aftermarket Outboard Impeller Water Pump Repair Kit. Fits 3B2-87322-2 Tohatsu.Part Water Pump Impeller Repair Kits Replacement for 803750A03 803748Q01 803748K01 || 😀【Kit Includes】 WATER PUMP IMPELLER， PUMP CASE LINER， PUMP CASE GASKET， WATER PUMP GUIDE PLATE， GUIDE PLATE GASKET， BOLT， WASHER， PUMP CASE GASKET (LOWER)， SPRING PIN 3-10. || 😀【Applicable Models】 Fits Tohatsu M6/8/9.8B (2-Stroke) & MFS6BZ/8/9.8B (4-Stroke) || 😀【High Quality】 Made to meet or exceed OEM specifications. Extremely high quality metal alloys and modern neoprene which keep a spare in the toughest marine environment.
RUIJADE 😀【3B2-87322-2】 This is Top Quality Aftermarket Outboard Impeller Water Pump Repair Kit. Fits 3B2-87322-2 Tohatsu.Part Water Pump Impeller Repair Kits Replacement for 803750A03 803748Q01 803748K01 || 😀【Kit Includes】 WATER PUMP IMPELLER， PUMP CASE LINER， PUMP CASE GASKET， WATER PUMP GUIDE PLATE， GUIDE PLATE GASKET， BOLT， WASHER， PUMP CASE GASKET (LOWER)， SPRING PIN 3-10. || 😀【Applicable Models】 Fits Tohatsu M6/8/9.8B (2-Stroke) & MFS6BZ/8/9.8B (4-Stroke) || 😀【High Quality】 Made to meet or exceed OEM specifications. Extremely high quality metal alloys and modern neoprene which keep a spare in the toughest marine environment.
Number on catalog scheme: -
Compatible models:
1B08201DB
Mercury
Mercury entire parts catalog list:
Information:
1. Remove bolt (1), six bolts (2), two top bolts, housing (4) and the gasket. 2. Remove governor spring (5), the two wave washers, one flat washer and seat from the guide in the housing. 3. Remove bolts (6), cover (7) and the gasket from the housing. Use tooling (A) to remove seal (8) from the cover. 4. Remove low idle adjustment screw (9) and spring (10) from the housing. 5. Remove shaft assembly (12), lever (11) and lever (13) from the housing. 6. Remove two snap rings from pins (15) and remove pins (15). Remove plates (14) and stop (16) from the shaft assembly. 7. Remove pin (18), pin (17) and spring (19) from the shaft assembly. 8. Remove shaft (20) and lever (21) from the housing.
Remove check valve (22) only if a replacement is necessary. The check valve will be damaged during removal.
9. Remove check valve (22) if a replacement is necessary. 10. Remove contact (23) and body (24) for the governor dashpot adjustment screw from the housing.11. Remove bolts (25), cover (26) and the gasket from the housing. 12. Remove seal (27) and adjustment screw (28) for the high idle. 13. Remove two bolts (29), housing (30) and the gasket from the fuel injection pump housing. 14. Remove bolts (31) and torque control group (32).15. Disassemble the torque control group and inspect the spacer, spring and insulator for damage or wear. 16. Remove bolts (34) and block (33) for the full load stop from the housing. 17. Remove the bolt that holds collar (35) to bolt (37). Remove collar (35) and spring (36) from bolt (37). Remove bolt (37) from the block.18. Remove the stop screw from collar (35), if a replacement is necessary. 19. Remove bolts (39) and governor servo (38) from the fuel injection pump. 20. Remove lockring (44), seat (43), spring (broken link spring) (42) and sleeve (41) from valve (40). Remove the other lockring (44) from the groove in the center of valve (40). 21. Remove valve (40), sleeve (45) and piston (47) from the governor servo. Remove the O-ring seal from sleeve (45).22. Remove pin (46) and lever (48) from the governor servo. 23. Use tool (B) to hold spring (50) in compression so ring (49) can be removed. Spring (50) is used to put a preload on the thrust bearing for the camshaft in the fuel injection pump housing.24. Remove ring (49) then remove tool (B). 25. Remove bearing (51), sleeves (52) and spring (50) from the governor shaft. 26. Remove ring (53) and dashpot assembly (54) from the governor shaft. 27. Use tool (C) to remove snap ring (60) from seat (57). Remove ring (59) and spool (58) from seat (57).28. Remove seat (57) from spring (56) and remove spring (56) from seat (55). 29. Remove spring (overfueling spring) (61) and riser (62) from the governor shaft. 30 Remove ring (63), races (64) and bearing (65) from the riser. 31. Use a screwdriver to remove shield (66) as shown. Make a replacement of shield (66) any time it is removed. 32. Remove bolts (67) and carrier (68) for the governor flyweights. 33. Remove dowels (69) and flyweights (71) from the carrier.34. Remove shaft (70) from the carrier. Remove the dowel from shaft (70). 35. Remove races (72) and bearing (73) from the camshaft in the fuel injection pump housing.Assemble Governor
Put clean oil on all parts before assembly. Be sure all oil passages are clear. 1. Install one race (72), bearing (73) and the other race (72) on the camshaft in the fuel injection pump housing. 2. Put flyweights (71) in position on carrier (68) and install the dowels to hold the flyweights in place. The flyweights must move freely on the dowels and have 0.010 to 0.23 mm (0.0004 to 0.009 in.) end play. 3. Install dowel (74) in governor shaft (70) and install the governor shaft in the carrier as shown. 4. Put carrier (68) in position on the camshaft and install bolts (67) that hold the carrier in place. Make a replacement of shield (66) any time it is removed.5. Inltall shield (66) on the carrier and use tool (D) to push the shield against its seat. Use a hammer and punch to move the metal (stake) two places on the side of the shield 180° 15° apart next to the holes in the shield. 6. Install one race (64), bearing (65) the other race (64) and use tool (C) to install the ring on riser (62) as shown. 7. Install riser (62) and spring (overfueling spring) on the governor shaft as shown. 8. Assemble the dashpot as follows:a. Install spring (56) on seat (55) and install seat (57) in spring (56).b. Put spool (58) and ring (59) in position on seat (57) and use tool (C) to install snap ring (60) to hold them in place. 9. Install dashpot assembly (54) on the governor shaft as shown. 10. Install ring (53) in the lower groove in the governor shaft. Install one sleeve (52), spring (50), the other sleeve (52) and bearing (51) on the governor shaft as shown. Spring (50) is used to put a preload on the thrust bearing on the camshaft in the fuel injection pump housing. 11. Use tool (B) to hold spring (50) in compression and install ring (49) in the groove in the governor shaft. Remove tool (B). 12. Put lever (48) in position on the governor servo and install pin (46) to hold the lever in place. Use a hammer and chisel to move the metal (stake) four places 90° apart on the outside surface on both legs of the governor servo to hold pin (46) in place.13. Install the O-ring seal on sleeve (45). Install piston (47) and sleeve (45) in the governor servo as shown.14. Install valve (40) in the governor servo as shown. 15. Install one lockring (44) in the groove near the center of valve (40). Put sleeve (41), spring (broken link spring) (42)
Remove check valve (22) only if a replacement is necessary. The check valve will be damaged during removal.
9. Remove check valve (22) if a replacement is necessary. 10. Remove contact (23) and body (24) for the governor dashpot adjustment screw from the housing.11. Remove bolts (25), cover (26) and the gasket from the housing. 12. Remove seal (27) and adjustment screw (28) for the high idle. 13. Remove two bolts (29), housing (30) and the gasket from the fuel injection pump housing. 14. Remove bolts (31) and torque control group (32).15. Disassemble the torque control group and inspect the spacer, spring and insulator for damage or wear. 16. Remove bolts (34) and block (33) for the full load stop from the housing. 17. Remove the bolt that holds collar (35) to bolt (37). Remove collar (35) and spring (36) from bolt (37). Remove bolt (37) from the block.18. Remove the stop screw from collar (35), if a replacement is necessary. 19. Remove bolts (39) and governor servo (38) from the fuel injection pump. 20. Remove lockring (44), seat (43), spring (broken link spring) (42) and sleeve (41) from valve (40). Remove the other lockring (44) from the groove in the center of valve (40). 21. Remove valve (40), sleeve (45) and piston (47) from the governor servo. Remove the O-ring seal from sleeve (45).22. Remove pin (46) and lever (48) from the governor servo. 23. Use tool (B) to hold spring (50) in compression so ring (49) can be removed. Spring (50) is used to put a preload on the thrust bearing for the camshaft in the fuel injection pump housing.24. Remove ring (49) then remove tool (B). 25. Remove bearing (51), sleeves (52) and spring (50) from the governor shaft. 26. Remove ring (53) and dashpot assembly (54) from the governor shaft. 27. Use tool (C) to remove snap ring (60) from seat (57). Remove ring (59) and spool (58) from seat (57).28. Remove seat (57) from spring (56) and remove spring (56) from seat (55). 29. Remove spring (overfueling spring) (61) and riser (62) from the governor shaft. 30 Remove ring (63), races (64) and bearing (65) from the riser. 31. Use a screwdriver to remove shield (66) as shown. Make a replacement of shield (66) any time it is removed. 32. Remove bolts (67) and carrier (68) for the governor flyweights. 33. Remove dowels (69) and flyweights (71) from the carrier.34. Remove shaft (70) from the carrier. Remove the dowel from shaft (70). 35. Remove races (72) and bearing (73) from the camshaft in the fuel injection pump housing.Assemble Governor
Put clean oil on all parts before assembly. Be sure all oil passages are clear. 1. Install one race (72), bearing (73) and the other race (72) on the camshaft in the fuel injection pump housing. 2. Put flyweights (71) in position on carrier (68) and install the dowels to hold the flyweights in place. The flyweights must move freely on the dowels and have 0.010 to 0.23 mm (0.0004 to 0.009 in.) end play. 3. Install dowel (74) in governor shaft (70) and install the governor shaft in the carrier as shown. 4. Put carrier (68) in position on the camshaft and install bolts (67) that hold the carrier in place. Make a replacement of shield (66) any time it is removed.5. Inltall shield (66) on the carrier and use tool (D) to push the shield against its seat. Use a hammer and punch to move the metal (stake) two places on the side of the shield 180° 15° apart next to the holes in the shield. 6. Install one race (64), bearing (65) the other race (64) and use tool (C) to install the ring on riser (62) as shown. 7. Install riser (62) and spring (overfueling spring) on the governor shaft as shown. 8. Assemble the dashpot as follows:a. Install spring (56) on seat (55) and install seat (57) in spring (56).b. Put spool (58) and ring (59) in position on seat (57) and use tool (C) to install snap ring (60) to hold them in place. 9. Install dashpot assembly (54) on the governor shaft as shown. 10. Install ring (53) in the lower groove in the governor shaft. Install one sleeve (52), spring (50), the other sleeve (52) and bearing (51) on the governor shaft as shown. Spring (50) is used to put a preload on the thrust bearing on the camshaft in the fuel injection pump housing. 11. Use tool (B) to hold spring (50) in compression and install ring (49) in the groove in the governor shaft. Remove tool (B). 12. Put lever (48) in position on the governor servo and install pin (46) to hold the lever in place. Use a hammer and chisel to move the metal (stake) four places 90° apart on the outside surface on both legs of the governor servo to hold pin (46) in place.13. Install the O-ring seal on sleeve (45). Install piston (47) and sleeve (45) in the governor servo as shown.14. Install valve (40) in the governor servo as shown. 15. Install one lockring (44) in the groove near the center of valve (40). Put sleeve (41), spring (broken link spring) (42)
Parts repair Mercury:
803748K02
803748Q02
853792T06
803748K01