809556 Mercury RETAINER


809556 RETAINER Mercury 1F50412RD RETAINER
809556 RETAINER Mercury
Rating:
33

Buy RETAINER 809556 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 2
 

Compatible models:

1F50412RD   Mercury

Mercury entire parts catalog list:

1F50412RD 1995,1996,1997,1998

Information:


Table 1
Diagnostic Codes Table
Description Conditions which Generate this Code System Response
545-5 Ether Start Relay open/short to +batt The Electronic Control Module (ECM) detects an open circuit and/or a short to the +Battery at the output to the ether start relay. The code is logged.
Ether injection is disabled.
545-6 Ether Start Relay short to ground The ECM detects a short circuit to ground at the output to the ether start relay.
The ECM has been powered for at least two seconds. When the engine is in auto mode, the engine uses an ether injection system to improve starting in cold temperatures. The duration of the ether cycle is based on the engine coolant temperature. The ECM, which controls the ether injection system, uses the engine coolant temperature sensor to detect engine temperature. The ECM determines if ether should be injected by monitoring actual engine rpm and the engine temperature. The ECM will activate the ether start relay if the engine coolant temperature is below a set temperature and the engine rpm is below a certain level. The ether injection system becomes enabled at 10 °C (50 °F). The ether injection system will run for a minimum of 10 seconds up to a maximum of 130 seconds at −40 °C (−40 °F). The automatic ether injection system is disabled whenever engine rpm exceeds 1900 rpm or the engine coolant temperature exceeds 10 °C (50 °F).The ether injection system can also be operated in manual mode. The ether injection system is switched into manual mode whenever the starting aid switch is depressed. Ether is injected in manual mode if the starting aid switch is depressed and the coolant temperature is below the maximum limit. The manual mode will allow ether to be injected for a maximum of 130 seconds when the switch is toggled. Manual mode allows ether to be injected whenever the coolant temperature is less than 10 °C (50 °F) and engine rpm is greater than 50 rpm.Note: The ether function will be disabled if the ether control parameter is disabled.
Illustration 1 g01258710
Typical schematic
Illustration 2 g01213344
P1 ECM connector
(P1-5) Digital return
(P1-20) Ether aid switch
Illustration 3 g01213347
P2 ECM connector
(P2-10) Ether start relay
Illustration 4 g01234146
Location of ECM connectors
Illustration 5 g01258712
Connector "A"
(Terminal 25) Digital return
Illustration 6 g01258713
Connector "B"
(Terminal 31) Ether aid switch
(Terminal 32) Ether start relay
Personal injury or death can result from using ether.Failure to follow these instructions could result in an explosion and/or fire and possible personal injury.When using starting fluid, follow the manufacturer's instructions carefully. Use ether sparingly and spray it only while cranking the engine. Also, do not store starting fluid containers in the cab.
The ether canister must be removed prior to activating this test.
Do not perform this procedure within 15 M (50 ft) of an open flame.
Do not allow the ether injection system to be on for more than two minutes. Damage to the ether solenoid may occur.
Test Step 1. INSPECT ELECTRICAL CONNECTORS AND WIRING
Turn the breaker for the ECM to the OFF position.
Thoroughly inspect the J1/P1 ECM connector and the J2/P2 ECM connector. Inspect all of the connectors that are associated with the circuit. Refer to Troubleshooting, "Inspecting Electrical Connectors" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connectors that are associated with the circuit.
Check the ECM connector (allen head screw) for the proper torque. Refer to Troubleshooting, "Inspecting Electrical Connectors" for details.
Check the harness and wiring for abrasion and for pinch points. Expected Result:All connectors, pins and sockets are completely coupled and/or inserted and the harness and wiring are free of corrosion, of abrasion and of pinch points.Results:
OK - The harness and connectors appear to be OK. Proceed to Test Step 2.
Not OK - There is a problem with the connectors and/or wiring.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that


Parts retainer Mercury:

812443 1
 
812443 1 RETAINER
1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 10402139D, 1040213YL, 1041312UB, 10432037D, 1043203DD, 1043203VD, 1043213DD, 1043302DD, 1043411DD, 1043412DB, 1043412DD, 1050302DB, 1050302FB, 1050302FD, 1050302SD, 1050312FB, 1050312LD, 1050411D
822441
RETAINER
822441 RETAINER
1006201DB, 1006201PD, 1006201RB, 1006201VB, 1006211RD, 1008211RD, 1010207VB, 1011201DB, 1016207PD, 1016207RB, 1016207SB, 10202014D, 1020201DB, 1020201VB, 1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040213YL, 1041312UB, 10432037D, 1043203D
822459
RETAINER
822459 RETAINER
10202014D, 1020201DB, 1020201VB, 1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040213YL, 1041312UB, 10432037D, 1043203DD, 1043203VD, 1043213DD, 1043302DD, 1043411DD, 1043412DB, 1043412DD, 1050302DB, 1050302FB, 1050302FD, 1050312FB, 1050411D
821827
RETAINER-SHIFT SHAFT
821827 RETAINER-SHIFT SHAFT
1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040213YL, 1041312UB, 10432037D, 1043203DD, 1043203VD, 1043213DD, 1043302DD, 1043411DD, 1043412DB, 1043412DD, 1050302DB, 1050302FB, 1050302FD, 1050312FB, 1050411DD, 1050412DB, 1050412DD, 1050412F
825017
RETAINER
825017 RETAINER
1A30302ZB, 1A40302FD, 1A41412ZB, 1B25203ZB, 1F25201UD, 1F25203VD, 1F30203VD, 1F30203ZB, 1F40203FD, 1F40452YB, 1F41452YD, 1F50352VD, 1F50412RD, 1F51452YB
822650
RETAINER-VALVE SPRING
822650 RETAINER-VALVE SPRING
1A30302ZB, 1A40302FD, 1A40311FZ, 1A41412ZB, 1A41452EZ, 1A41452FU, 1A51411HZ, 1A51412HZ, 1A51452EZ, 1A60351EZ, 1A60412HZ, 1A60452EZ, 1A60452HZ, 1A60463EZ, 1A6C411KZ, 1A6C413KZ, 1B25203ZB, 1E41412HB, 1E41452HB, 1E51412HB, 1E51412HZ, 1E60403HZ, 1E60412H
826587
 
826587 RETAINER
1F25201UD, 1F25203VD, 1F30203VD, 1F40452YB, 1F41452YD, 1F50352VD, 1F50412RD, 1F51452YB
827707 1
 
827707 1 RETAINER
1A30302ZB, 1A40302FD, 1A40311FZ, 1B25203ZB, 1F25201UD, 1F25203VD, 1F30203VD, 1F30203ZB, 1F40203FD, 1F40213FZ, 1F40452YB, 1F50352VD, 1F50412RD, 1F51452YB
Back to top